manualshive.com logo in svg

VESEYS MANTIS, Руководство пользователя

Поделиться
Скачать
VESEYS MANTIS Скачать руководство пользователя страница 7

7

ASSEMBLY 

(continued)

HOW TO ASSEMBLE
LOWER HANDLES

   To identify part numbers, see

pages 6 and 27.

   1. Use the protective

cardboard sleeve to stabilize
your tiller. Stand the engine
assembly (#8) up.

   2. Lay the handle parts within

easy reach. You’ll need one of the
handle clamps (#38) and one of
the lower handles (#3). Note that
the lower handles have a short leg
on one end. (Picture 1)

   3. Fit the handle clamp along the

outside of the short leg. Line up
the holes on the clamp and the leg.

   4. Choose one of the two 3-inch

(7.62 cm) bolts (#36). Slide it
through the first set of holes —
near the elbow where the lower
handle curves. (Picture 2)

   5. Now slide the other lower

handle onto the 3-inch (7.62 cm)

bolt. (Picture 3.) Fit the other
clamp onto this other handle’s
short leg. Add a nut and tighten
finger tight.

   6. Locate the worm gear

housing. It starts just above — 
and extends down through — the
tiller’s red fender guard. You’ll
notice that there’s a recessed
channel on either side of the
housing’s top. (Picture 4.)

   7. Take the lower handles that

you’ve just put together. Slide
them into the two recessed
channels.

Make sure you insert them 

from the rear of the tiller (gasoline
tank faces the operator) . . . so that
the bolt fits along the back of the
housing. (Picture 5)

   8. Slide the second 3-inch (7.62

cm) bolt through the second set of
holes in the short legs. Add a nut
and tighten finger tight.

Picture 1

Picture 2

Picture 3

Picture 4

Picture 5

NOTE:

THE LOCK NUTS ARE STAMPED. FINGER TIGHT IS

APPROXIMATELY 1/2 TO 1-1/2 TURNS.

!

401773 Vesey Tiller NewHndl 5YW_Mantis Tiller Manual Grn 401703  12/15/10  3:10 PM  Page 7

Содержание MANTIS

































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды