VESDA VLC Скачать руководство пользователя | Manualshive

Страница: 23 / 58

background image

VESDA

VESDA Maintenance Guide

www.xtralis.com

17

8

Replacing Detector Components

8.1

VESDA VLP and VESDA VLS

8.1.1

Replacing VESDA VLP and VESDA VLS Filter Cartridges

The service interval of an air filter depends upon the environment. You can use the LCD Programmer or Xtralis
VSC software to change the service interval for filters. The system will generate a minor fault when the filter
has reached 80% and an urgent fault when it reaches 120% of its capacity. We recommend that the
installation date and replacement date be written on the air filter cartridge label as a physical reminder of when
the next service is expected.

Note:

The detector must have the power turned on while the air filter cartridge is being replaced.

Replacement Procedure

1. Slide down and remove the air filter cover (A) in Figure 8-1 below.
2. Unscrew the recessed phillips head screw (B) in Figure 8-1 below.

Figure 8-1: Replacing air filters in VESDA VLP and VESDA VLS detectors

3. Pull out the air filter cartridge (C) in Figure 8-1 above. This will stop the aspirator. If the aspirator does not

stop, replace the filter switch.

4. Insert the replacement air filter cartridge (VSP-005).
5. Tighten the filter screw.
6. Replace the air filter cover.
7. Reset the filter counter using either the LCD Programmer or a PC running Xtralis VSC.

«
...
21
22
23
24
25
...
»

Содержание VLC



























































Отзывы:

Нет отзывов

Похожие инструкции для VLC

Бренд: S Fire Страницы: 2

Бренд: Pit Boss Страницы: 18

Бренд: Autool Страницы: 13

Бренд: SEBSON Страницы: 12

Бренд: Xpresskit Страницы: 20

Бренд: ZETTLER Страницы: 21

Бренд: Lenoxx Страницы: 7

Бренд: Silvercrest Страницы: 28

Бренд: Silvercrest Страницы: 46

Бренд: Silvercrest Страницы: 62

Бренд: Silvercrest Страницы: 69

Бренд: Silvercrest Страницы: 98

Бренд: Silvercrest Страницы: 140

Бренд: Silvercrest Страницы: 199

Бренд: NUTRICHEF Страницы: 6

Бренд: AUTHOR Alarm Страницы: 52

Бренд: Equity Страницы: 2

Бренд: Equity Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды