VESDA VESDA-E VES-A00-P Скачать руководство пользователя страница 11 | Manualshive

Страница: 11 / 124

VESDA VESDA-E VES-A00-P Скачать руководство пользователя страница 11

VESDA-E VES-A00-P Product Guide

www.xtralis.com

5

2

Product Information

2.1

Detector Components

The VES-A00-P detector contains field-replaceable Filter, Aspirator and Chamber Assembly components.
These are shown below in Figure 2-1.

B

C

D

E

F

G

Legend

A

Fascia

B

Filter

C

Chamber Assembly

D

Aspirator

E

Sampling Module

F

Base

G

Ultrasonics Flow
Sensing and Scanning
Module

Figure 2-1: Detector components

Refer to Chapter 7 for further information regarding maintenance scheduling and availability of spare parts.

2.2

How the VES-A00-P works

An air sampling pipe network collects samples from the protected area. The integrated aspirator draws air into
the sampling pipe(s).

The air from each sampling pipe passes through a valve and an air flow sensor and a sample of the air is then
drawn into the smoke detection chamber via the sampling module, after first passing through the replaceable
filter.

A further filter provides filtered clean air to protect the optical surfaces inside the detection chamber from
contamination.

The detection chamber uses a short wavelength laser light source in conjunction with photodiodes and
advanced imaging technology to achieve optimum response to a wide range of smoke types.

The VES-A00-P draws air from all sectors in use. If the smoke level reaches the Adaptive Scan Threshold,
the VES-A00-P quickly scans each sector to identify which sector is carrying smoke. The Adaptive Scan
Threshold starts at one quarter of the lowest Alert threshold and self-adjusts to minimize unnecessary scans if
they occur.

Once this fast initial scan is completed the VES-A00-P continues to monitor all four sectors. The sector with
the highest smoke during the initial scan is preferentially scanned so as to provide the fastest response.

«
...
9
10
11
12
13
...
»

Содержание VESDA-E VES-A00-P





























































































































Отзывы:

Нет отзывов