VESDA VESDA-E VES-A00-P Скачать руководство пользователя страница 105

Страница: 105 / 124

VESDA-E VES-A00-P Product Guide

www.xtralis.com

Figure 7-25: Remove the three screws holding the Ultrasonics Flow Sensing and Scanning Module

4. Remove the Ultrasonics Flow Sensing and Scanning Module from the detector base. (Figure 7-26)

Figure 7-26: Remove the Ultrasonics Flow Sensing and Scanning Module

Installing the replacement Ultrasonics Flow Sensing and Scanning Module

1. Re-install the Ultrasonics Flow Sensing and Scanning Module into the detector base ensuring that the

looms are not trapped under the module.

2. Secure the three screws that hold the Ultrasonics Flow Sensing and Scanning Module to the detector

base.

3. Reconnect the main board loom connection at J2 and antenna connection at J11.

Содержание VESDA-E VES-A00-P





























































































































Результаты поиска

Содержание VESDA-E VES-A00-P

Отзывы:

Похожие инструкции для VESDA-E VES-A00-P

Бренды по названию

Популярные бренды

VESDA VESDA-E VES-A00-P, Руководство по эксплуатации продукта

Результаты поиска

Содержание VESDA-E VES-A00-P

Отзывы:

Похожие инструкции для VESDA-E VES-A00-P

Бренды по названию

Популярные бренды