manualshive.com logo in svg

Verus Engineering ZC6, Инструкция по установке

Поделиться
Скачать
Verus Engineering ZC6 Скачать руководство пользователя страница 12

 

 

 12 

3/6/2016 

 

Author: Eric Hazen 

Date: 2017/02/19 

Recipients: Public  

 

ENGINEERING | NORTH AMERICA 

REVISION: R02 

Confidential: Property of Verus Engineering. Not for Distribution outside intended recipient list. 

 

Verus Engineering 
[email protected]

 

ZC6 / ZN6 Street Front Splitter and Race Upgrade – Install Manual 
 

 

 

 

3.8.

 

Then 

on each side of the car in the wheel wells, remove 4 plastic screw pins.  Three are 

located down low (see below photo), the last one is up by the turn signal on the inside of the 
fender.  Ignore that the splitter is installed in this photo, it was taken after the installation.

 

 

 

3.9.

 

The 

turn signal has to be removed to expose the final plastic push pin and then the front 

bumper will come off.  There is a metal tab that needs to be push towards the 

*front*

 of the 

car.  The arrow in the picture shows this well.  I used a flat head screwdriver to push this 
forward and then gently pried the signal away from the car.

 

 

Содержание ZC6




















Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды