background image

 

 

Vertiv™ NetSure™ 211 SERIES -48 VDC Battery Cabinet Installation & User Manual (Section 6023)

 

|

 

Rev. L 

Battery 

Refer to the battery manufacturer documentation for specific battery safety instructions.  The following are 
general guidelines. 

 

WARNING!  

Correct polarity must be observed when connecting battery leads. 

 

 

WARNING!  

Special safety precautions are required for procedures involving handling, installing, and 

servicing batteries.  Observe all battery safety precautions in this manual and in the battery instruction 
manual.  These precautions should be followed implicitly at all times. 

 

WARNING!  

A battery can present a risk of electrical shock and high short circuit current.  Servicing of 

batteries should be performed or supervised only by properly trained and qualified personnel 
knowledgeable about batteries and the required precautions. 

 

The following precautions should be observed when working on batteries: 

 

Follow the recommended PPE requirements per the SDS for the battery to be used. 

 

Batteries are an energy source that can produce high amounts of electrical current. 

 

Remove watches, rings, and other metal objects. 

 

Eye protection should be worn to prevent injury from accidental electrical arcs. 

 

Use certified and well maintained insulated tools.  Use double insulated tools appropriately rated for 
the work to be performed.  Ensure that wrenches with more than one working end have only one 
end exposed. 

 

Do not lay tools or metal parts on top of batteries. 

 

Verify that no current will flow when the battery is connected or disconnected by opening battery 
disconnects (if available) or adjusting the system to match battery voltage. 

 

Risk of explosion if battery is replaced with an incorrect type or if polarity is reversed.  
Recommended to replace batteries with the same manufacturer and type, or equivalent. 

 

Dispose of used batteries according to the instructions provided with the batteries.  Do not dispose 
of batteries in a fire.  They may explode. 

 

Batteries may generate explosive gases during normal operation.  Systems containing batteries 
should never be installed in an airtight room or space.  Only install in a ventilated environment. 

 

Batteries may contain sulfuric acid.  If battery acid enters your eye, immediately flush your eye with 
running cold water for at least 15 minutes.  Get medical attention immediately.  If battery acid 
contacts skin or clothing, wash immediately with soap and water. 

 

Do not open or mutilate batteries. 

 

ALWAYS FOLLOW THE BATTERY MANUFACTURER’S RECOMMENDATIONS AND SAFETY 
INSTRUCTIONS. 

Содержание NetSure 211 Series





























Отзывы: