Vertiv Liebert MBX Скачать руководство пользователя страница 10 | Manualshive

Страница: 10 / 34

Vertiv Liebert MBX Скачать руководство пользователя страница 10

Torque the Power End Feed Box interior 3-phase live and neutral conductor connections according to

Electrical Connection Torque Specifications

on page 10. For units equipped with monitoring, the voltage

sense leads are torqued to 7.4 ft.-lb. (10Nm) for 3-phase and neutral conductors; the monitoring ground is
torqued to 3 ft.-lb. (4Nm).

If the monitoring option is included in your system, refer to SL-70526 for detailed monitoring setup
information.

Figure 2.4 Applicable Hardware Stack for Electrical Torque Specifications

ITEM

DESCRIPTION

1

Bolt

2

Belleville Washer

3

Flat Washer

4

Nut

Table 2.4 Torque Specification Overview

HARDWARE

1 BELLEVILLE WASHER

2 BELLVILLE WASHERS

1/4 in. (M6/10mm)

40 in.-lb. (4.5Nm)

80 in.-lb. (9.0Nm)

5/16 in. (M8/13mm)

80 in.-lb. (9.0Nm)

160 in.-lb. (18.0Nm)

3/8 in. (M10/17mm)

120 in.-lb. (13.6Nm)

240 in.-lb. (27.1Nm)

1/2 in. (M12/19mm)

480 in.-lb. (54.2Nm)

—

Table 2.5 Electrical Connection Torque Specifications

Vertiv™ | Liebert® MBX Busway System Installer/User Guide

10

«
...
8
9
10
11
12
...
»

Содержание Liebert MBX



































Отзывы:

Нет отзывов