Vertiv Liebert DSE Скачать руководство пользователя страница 47

Страница: 47 / 120

9 HEAT-REJECTION SKID

9.1 Planning Dimensions

The unit dimensions are described in the submittal documents included in the

Submittal Drawings

page 67.

The following table lists the relevant documents by number and title.

Document Number

Title

DPN004259

Cabinet Dimensional Data, MCV440, Single skid

DPN004261

Cabinet Dimensional Data, MCV440, Dual skid

Table 9.1 Dimension Planning Drawings

9.2 Liebert MCV Match-up Selections

Outdoor Design Ambient Temp.,

°F (°C)

Maximum Return Air Temp.,

°F (°C)

DSE Models

DA250

Up to 105 (41)

85 (29) to 105 (41)

MCV440

Table 9.2 High-efficiency Condenser Match-ups

9.3 Liebert MCV Electrical Power Requirements

Condenser-rated voltage should be verified with available power supply before installation. Refer to the

unit’s electrical schematic and serial tag for specific electrical requirements. Line voltage electrical service

is required for all condensers at the location of the condenser.

For the most reliable operation of the system, the indoor unit and the MCV condenser should be on the

same power source. The Liebert® DSE system offers an option for a power feed from the active source on

the indoor unit to the outdoor condenser. This configuration provides the greatest reliability and fastest

recovery during power loss or source change.

When powering the outdoor condenser from the indoor unit, there is a breaker/fuse on the indoor unit

and the wire sizing requirements are provided in Table 9.3 on the next page.

A unit disconnect is standard on the MCV skid. However, a site disconnect may be required per local code

to isolate the unit for maintenance. Refer to the unit’s serial tag for specific condenser electrical

requirements (Table 9.3 on the next page).

Route the supply power to the site disconnect switch and then to factory-provided high-voltage

enclosure located on the MCV heat-rejection skid. Reference submittal drawings listed in Table 9.1

above.

9 Heat-rejection Skid

Содержание Liebert DSE

























































































































Результаты поиска

Содержание Liebert DSE

Отзывы:

Похожие инструкции для Liebert DSE

Бренды по названию

Популярные бренды

Vertiv Liebert DSE, Системное проектирование и руководство пользователя

Результаты поиска

Содержание Liebert DSE

Отзывы:

Похожие инструкции для Liebert DSE

Бренды по названию

Популярные бренды