Vertiv Liebert DSE Скачать руководство пользователя страница 34

Страница: 34 / 120

The electrical and unit-to-unit connections are described in the submittal documents included in the

Submittal Drawings

on page 67.

The following table lists the relevant documents by number and title.

Document Number

Title

DPN004797

Electrical Field Connections, Downflow, DA250

DPN003886

CANbus cable connections between indoor unit, Liebert® MCV condenser

Unit-to-Unit Networking

DPN004351

Liebert® iCOM Unit-to-unit Network Connections

Table 7.3 Electrical Field-connection Drawings

Document Number

Title

DPN004257

Condenser connection data, MCV440, Single skid

DPN004262

Condenser connection data, MCV440, Dual skid

Table 7.4 MCV Heat-rejection Skid Field-connection Drawings

WARNING! Arc flash and electric shock hazard. Open all local and remote electric power-supply

disconnect switches, verify with a voltmeter that power is Off and wear appropriate,

OSHA-approved personal protective equipment (PPE) per NFPA 70E before working within the

electric control enclosure. Failure to comply can cause serious injury or death. Customer must

provide earth ground to unit, per NEC, CEC and local codes, as applicable. Before proceeding

with installation, read all instructions, verify that all the parts are included and check the

nameplate to be sure the voltage matches available utility power. The Liebert® controller does

not isolate power from the unit, even in the “Unit Off” mode. Some internal components require

and receive power even during the “Unit Off” mode of the controller. The factory-supplied

disconnect switch is inside the unit. The line side of this switch contains live high-voltage. The

only way to ensure that there is NO voltage inside the unit is to install and open a remote

disconnect switch. Refer to unit electrical schematic. Follow all local codes.

WARNING! Risk of electric shock. Can cause equipment damage, injury or death. Open all local

and remote electric power supply disconnect switches and verify with a voltmeter that power is

off before working within any electric connection enclosures. Service and maintenance work

must be performed only by properly trained and qualified personnel and in accordance with

applicable regulations and manufacturers’ specifications. Opening or removing the covers to

any equipment may expose personnel to lethal voltages within the unit even when it is

apparently not operating and the input wiring is disconnected from the electrical source.

WARNING! Risk of improper wire sizing/rating and loose electrical connections. Can cause

overheated wire and electrical connection terminals resulting in smoke, fire, equipment and

building damage, injury or death. Use correctly sized copper wire only and verify that all

electrical connections are tight before turning power On. Check all electrical connections

periodically and tighten as necessary.

Vertiv | Liebert® DSE™ System Design and User Guide

Содержание Liebert DSE

























































































































Результаты поиска

Содержание Liebert DSE

Отзывы:

Похожие инструкции для Liebert DSE

Бренды по названию

Популярные бренды

Vertiv Liebert DSE, Системное проектирование и руководство пользователя

Результаты поиска

Содержание Liebert DSE

Отзывы:

Похожие инструкции для Liebert DSE

Бренды по названию

Популярные бренды