Vertical Technologies DeltaQuad Evo Скачать руководство пользователя | Manualshive

Страница: 14 / 126

background image

Charging the LiPo

If you have ordered the DeltaQuad with a LiPo battery it will come with a plug & play charger. This charger
can charge an empty LiPo battery in approximately 6 hours. To charge the battery insert both the power and
balance plugs in the charger, it will commence charging automatically. When the LED light on the charger
turns green the LiPo will have been charged.

The DeltaQuad LiPo can also be charged using a high current charging solution and is capable of charging
within 1 hour if your charger is capable of providing 20 Amperes. Charging at this rate will limit the durability
of the LiPo, it is recommended to charge the LiPo at no more than 5 Amperes for a maximum lifetime.

1. Remove the battery from the vehicle. The battery should never be charged inside the vehicle.

2. Never charge batteries unattended unless you can charge them inside a LiPo safe.

3. Charge in an isolated area, away from other flammable materials.

4. Ensure the battery is at ambient temperature before charging.

Storing the LiPo

The LiPo should be stored in a safe and dark location between 5 and 30 degrees Celsius. If the battery has
been fully discharged, it is recommended to put at least some charge (+- 50%) before long term storage.

Telemetry & Ground Control

In this section we cover the setup of your Ground Control Station, Video and Telemetry links. For information
on using the ground control station please refer to the

sections in this manual.

Installing QGroundControl

The DeltaQuad uses QGroundControl as its primary Ground Control Station.

If you have ordered a Ground Control Station with your DeltaQuad it will have been installed and tested
before it was shipped to you. You may skip this section and proceed to the installation of your telemetry link.

To install QGroundControl on your device please refer to the

QGroundControl Installation Manual

«
...
12
13
14
15
16
...
»

Содержание DeltaQuad Evo































































































































Отзывы:

Нет отзывов

Похожие инструкции для DeltaQuad Evo

Бренд: Airgineers Страницы: 6

Бренд: UDI R/C Страницы: 16

X-bee drone 5.2

Бренд: Overmax Страницы: 44

Бренд: MAGINON Страницы: 40

m200 Nano Drone

Бренд: sky viper Страницы: 12

Бренд: MALA Страницы: 2

X-Stream Video Drone

Бренд: Air Hogs Страницы: 2

Бренд: MJX R/C Страницы: 28

Бренд: GUARDO Страницы: 25

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды