Vertex Standard Spirit VXA-700, Руководство по обслуживанию

Страница: 16 / 40

16
Alignment
Wide FM S-meter (S-Full) Adjustment
r
Connect the Radio Tester to the antenna jack, and ad-
just its output level to +25 dBµ (with standard Wide
FM modulation: ±22.5 kHz deviation @ 1 kHz) at 98.000
MHz.
r
Set the transceiver to 98.000 MHz and turn the trans-
ceiver off.
r
Press and hold in the
PTT
switch,
MONITOR
switch,
and key while turning the transceiver on to enter
the alignment mode.
r
Rotate the
DIAL
selector knob to select “
WFM SM LV
xxx
.”
r
Press the key momentarily (you will hear a long
beep), then press and hold in the key (until you
hear a short beep).
r
Turn the transceiver off.
VOR Section
VOR Sensitivity Adjustment
r
Connect the Radio Tester to the antenna jack, and ad-
just its output level to +5 dBµ (with standard AM
modulation: 30 % AM modulation @ 1 kHz) at 108.000
MHz.
r
Set the transceiver to 108.000 MHz and turn the trans-
ceiver off.
r
Press and hold in the
PTT
switch,
MONITOR
switch,
and key while turning the transceiver on to enter
the alignment mode.
r
Rotate the
DIAL
selector knob to select “
VSTR Level
xxx
.”
r
Press the key momentarily (you will hear a long
beep), then press and hold in the key (until you
hear a short beep).
r
Turn the transceiver off.
VOR Sensitivity Hysteresis Adjustment
r
Connect the Radio Tester to the antenna jack, and ad-
just its output level +5 dBµ (with standard AM modu-
lation: 30 % AM modulation @ 1 kHz) at 108.000 MHz.
r
Set the transceiver to 108.000 MHz and turn the trans-
ceiver off.
r
Press and hold in the
PTT
switch,
MONITOR
switch,
and key while turning the transceiver on to enter
the alignment mode.
r
Rotate the
DIAL
selector knob to select “
VSTR HITH
xxx
.”
r
Press the key momentarily (you will hear a long
beep), then press and hold in the key (until you
hear a short beep).
r
Turn the transceiver off.
VOR Angle Adjustment
r
Connect the Avionics Radio Tester to the antenna jack.
r
Set the transceiver to 108.000 MHz, set up the “FROM”
mode (press + key, if necessary), and set the
Avionics Radio Tester as shown below.
Frequency : 108.000 MHz
Output Level : +40 dBµ
30 Hz VAR. : 30 %
9.96 kHz Carrier : 30 %
9.96 kHz MOD : 480 Hz
DIRECT : FROM
PHASE : 15 °
r
Note the difference of the phase indication between
the Transceiver’s indication and Avionics Radio
Tester’s indication, then turn the transceiver off.
r
Press and hold in the
PTT
switch,
MONITOR
switch,
and keys while turning the transceiver on to enter
the alignment mode.
r
Rotate the
DIAL
selector knob to select “
VOR Degree
xxx
.”
r
Press the key momentarily (you will hear a long
beep), then set the difference value that is noted step 3
above, using the
DIAL
selector knob.
r
Press and hold in the key (until you hear a short
beep).
r
Turn the transceiver off.
Resetting the CPU
If you are unable to gain control of the transceiver
(or if you want to clear all memories and settings to
their factory defaults), press and hold in the and
MONITOR
switches while turning the transceiver
on.