Vertex Standard HX750S, Руководство по настройке

Страница: 3 / 4

FCC ID: K6630323X30
IC ID: 511B-30323X30
Alignment
3/4
Vertex Standard Co., Ltd.
enter the alignment mode.
ˆ
Press the [
▼
] or [
▲
] key to select the display to [U po xx].
ˆ
Press the [ MEM ] key to enable adjustment of this Alignment Mode.
ˆ
Press the PTT key to transmit the transceiver, if necessary, press the [
▼
] or [
▲
] key to
adjust the output power to 6.0 W (±0.3 W).
ˆ
Press the [ MEM ] key to save the new setting.
ˆ
Press and hold the [ PWR ] key for 2 seconds to turn the transceiver off.
TX Power Adjustment (Hi Power)
ˆ
Connect the wattmeter and dummy load to the antenna jack.
ˆ
Set the transceiver to CH16 (156.800 MHz) with “High” power mode, then turn the
transceiver off.
ˆ
Press and hold in the PTT ,[SQL], [
▲
] and [
▼
] key while turn the transceiver on to
enter the alignment mode.
ˆ
Press the [
▼
] or [
▲
] key to select the display to [H PO xx]
ˆ
Press the [ MEM ] key to enable adjustment of this Alignment Mode.
ˆ
Press the PTT key to transmit the transceiver, if necessary, press the [
▼
] or [
▲
] key to
adjust the output power to 5.0 W (±0.3 W).
ˆ
Press the [ MEM ] key to save the new setting.
ˆ
Press and hold the [ PWR ] key for 2 seconds to turn the Transceiver off.
TX Power Adjustment (Medium Power)
ˆ
Connect the wattmeter and dummy load to the antenna jack.
ˆ
Set the transceiver to CH16 (156.800 MHz) with “Low” power mode, and then turn the
transceiver off.
ˆ
Press and hold in the PTT ,[ SQL ], [
▲
] and [
▼
] key while turn the transceiver on to
enter the alignment mode.
ˆ
Press the [
▼
] or [
▲
] key to select the display to [n PO xx]
ˆ
Press the [ MEM ] key to enable adjustment of this Alignment Mode.
ˆ
Press the PTT key to transmit the transceiver, if necessary, press the [
▼
] or [
▲
] key to
adjust the output power to 2.5 W (±0.2 W).
ˆ
Press the [ MEM ] key to save the new setting.
ˆ
Press and hold the [ PWR ] key for 2 seconds to turn the Transceiver off.
ˆ
TX Power Adjustment (LOW Power)
ˆ
Connect the wattmeter and dummy load to the antenna jack.
ˆ
Set the transceiver to CH16 (156.800 MHz) with “Low” power mode, and then turn the
transceiver off.
ˆ
Press and hold in the PTT , [SQL] , [
▲
] and [
▼
] key while turn the transceiver on to
enter the alignment mode.
ˆ
Press the [
▼
] or [
▲
] key to select the display to [L PO xx]
ˆ
Press the [ MEM ] key to enable adjustment of this Alignment Mode.
ˆ
Press the PTT key to transmit the transceiver, if necessary, press the [
▼
] or [
▲
] key to
adjust the output power to 1.0 W (±0.1 W).
ˆ
Press the [ MEM ] key to save the new setting.
ˆ
Press and hold the [ PWR ] key for 2 seconds to turn the Transceiver off.
Tx Deviation Adjustment
ˆ
Connect the Radio Tester to the antenna jack, and then adjust the Audio generator
output to 100 mV at 1 kHz.
ˆ
Set the transceiver to CH16 (156.800 MHz) with “Low” power mode, and then turn the