VersaLogic EPM-5 Скачать руководство пользователя страница 3

Страница: 3 / 52

EPM-5 Reference manual

iii

Product Release Notes

Rev 7 Release –

Production release.

See

KnowledgeBase article VT1597

for changes made to Rev. 7.00.

Rev 6 Release –

Production release.

For the latest BIOS and PLD updates, go to the

EPM-5 support page

See

KnowledgeBase article VT1568

for changes made to Rev. 6.00.

Rev 5 Release –

Production release.

Heat sink added to CPU to improve thermal margins.

BIOS upgraded to version 5.3.103. Results in lower power draw in sleep state (suspend-to-RAM).

Converted jumper block V3 into two separate blocks, V3 and V5.

Removed Ethernet EMI capacitors to allow auto MDI/MDIX operation.

[R5.01] New PLD code enables true 16-bit I/O transfers on ISA bus. See

KnowledgeBase article

VT1477

for the update instructions.

[R5.01] BIOS upgraded to version 5.3.104: Fixes Ultra DMA IDE modes in Linux, frees COM port
I/O resources.

[R5.07] BIOS revision improves LVDS panel dot clock rate at high resolution and PCI IRQ line
routing. PLD revision implements GNT-REQ synchronization with the PCI clock and IOCHRDY on
the ISA bus.

Rev 4 Release –

Production release.

ACPI pushbutton control jumper.

ISA IRQ5 removed.

RoHS compliance.

Rev 3 Release –

Charlie release.

USB 2.0.

Audio interface.

ACPI power management: standby, suspend to RAM support.

Rev 2 Release –

Beta release.

Rev 1 Release –

Pre-production only. No customer releases.

Support Page

The

EPM-5 support page

, at

http://www.VersaLogic.com/private/pumasupport.asp

, contains additional

information and resources for this product including:

Reference Manual (PDF format)

Operating system information and software drivers

Data sheets and manufacturers’ links for chips used in this product

BIOS information and upgrades

Utility routines and benchmark software

Note:

This is a private page for EPM-5 users that can be accessed only be entering this address directly. It

cannot be reached from the VersaLogic homepage.

Содержание EPM-5





















































Результаты поиска

Содержание EPM-5

Отзывы:

Бренды по названию

Популярные бренды

VersaLogic EPM-5, Справочное руководство

Результаты поиска

Содержание EPM-5

Отзывы:

Бренды по названию

Популярные бренды