I N D I A ' S F I R S T
S U P E R E F F I C I E N T FA N
USER MANUAL
Congratulations for becoming an owner of the
SUPERFAN. You have made an excellent choice and
we hope you enjoy all its capabilities.
This user manual explains how to use SUPERFAN.
Please read this manual before operating your
Superfan and keep it for your future reference.
Thank You.
VERSA DRIVES PRIVATE LIMITED.
LIST OF FAN PARTS
V1.1 Mar, 2013,
Revision:
Air delivery and power specifications changed in
section 1.2 and the mounting height from ceiling is mentioned.
PATENT PENDING.
Unpack the carton of Superfan and check whether
you have the following items.
1. Down rod
2. Top canopy
3. Bottom canopy
4. Shackle kit to fix the down rod with ceiling hook
5. Kit to fix the down rod with fan motor
6. Fan motor with leaf fixing screws
7. Remote (6 key or 9 key remote based on the
model of Superfan)
8. Leaf – 3 No’s.
5
4
1
2
TM
3
TM
8
6
7
T
M
BEFORE INSTALLING AND OPERATING YOUR
S U P E R FA N , P L E A S E R E A D S A F E T Y
INSTRUCTIONS CAREFULLY.
• Before installing or cleaning the fan, switch off
the power at the electricity panel and the
associated wall switch location
• Lock the electricity panel or securely fasten a
warning device, such as a tag to prevent power
from being switched on accidentally
• Wirings must be done by qualified electricians
only
SAFETY INSTRUCTIONS
• The fan must be mounted at
minimum height
of 1 foot from ceiling and 7 feet from the
floor
to prevent accidental contact with the fan
leaves.
• Do not bend the leaves while installing or
cleaning.
• Store the remote battery in a place where
children cannot reach. If a child accidentally
swallow’s the battery consult the doctor
immediately.
• Dispose the battery in a proper manner. Do not
dispose it in fire.
• Do not short or disassemble the remote
battery.
Superfan is India’s first super-efficient fan which is
designed to consume less amount of energy even
at high speed. Hence it will reduce your electricity
bill.
1.1. INTRODUCTION:
1.2. SPECIFICATIONS
SPECIFICATIONS ARE SUBJECT TO CHANGE
WITHOUT NOTICE
1.3. FEATURES
• Energy saving, more than 50% savings, lower
electricity bill.
• Sensor-less design for more reliability.
• Green manufacturing (ROHS electronics, VOC free
paint, Green packing).
• Remote control for speed command, no regulator
needed, save space on switch board.
• Indication of remote operation.
• High speed, high volume of air.
• Consistent speed in low voltage and varying
voltages.
• Power factor better than 0.9 and more air per watt.
• Less heat generated by fan motor, cool operation.
• No extra noise during operation from inverter
supply.
• More hours of operation with inverter.
• 2 years of warranty.
SUPERFAN CAN BE POWERED ON/OFF BY
USING A SIMPLE WALL SWITCH
Please do not connect any regulator to
your Superfan
Phase &
Neutral
wires
Fig 4
Terminal
Block
Fig 3
Washer
and nut
Cotter pin
Fig 2
Shaft
Slit end
Down rod
Fig 1
1.
Take out the fan motor
and place it
gently on a clean and soft surface.
2.
Fix the slit end
of the downrod onto the shaft using bolt, washer,
spring washer, and nuts. Ensure that it is fully
tightened
3.
Then put the cotter pin
into the bolt hole and bend its two ends apart, to
lock
4.
Connect two wires (for phase
(red wire) and neutral (black wire) connections) on
the other side of the terminal block. Then insert the
wires from the bottom side of the down rod to the
top side
5.
Insert the bottom canopy
(Top and bottom canopies are identified with
[Ref: Fig 1]
[Ref: Fig 2].
[Ref: Fig 3].
[Ref: Fig 4].
1.4. INSTALLATION INSTRUCTION
THERE SHOULD BE NO OBSTRUCTIONS
FOR THE FAN TO ROTATE AND OBJECTS
(LIKE WALL, OR POST) SHOULD BE AT
LEAST 2 FEET (~61 CM) AWAY FROM THE
TIP OF THE FAN LEAVES
B e f o r e m a k i n g / r e m o v i n g t h e
connections in the ceiling rose, please
switch off the power.
orientation of Superfan logo) from the topside of
the downrod. Insert the top canopy in an inverted
manner
6.
Fix the shackle kit in the
ceiling hook
7
. Fix the fan assembly in
the shackle using bolt, washer, spring washer, nuts
8.
Then tighten the nuts. Put the
cotter pin into the bolt hole and bend its two ends
apart to lock.
9.
Connect the phase and neutral
wires coming out from the downrod to the ceiling
rose as shown in the
.
Connect (Green/yellow)
earth
wire
to
the
screw
marked
as
" " on
the
[Ref: Fig 5].
[Ref: Fig 6].
[Ref: Fig 7].
Fig 8
Parameters
Input Voltage
(Vac)
Rated frequency
(Hz)
Span (mm)
Typical
Speed (rpm)
Typical Input
power (Watts)
Power factor
Air delivery
3
(m /min)
Speed control
Remote battery
160 to 265
48 to 52
1200
350
33
0.94
220
Super T2
Lithium coin battery 3V 165mAh
1200
385
33
0.94
230
Super T1
1400
275
38
0.94
270
Values
Super
A1
Super
X1
Super
V1
1
3
5
7
2
4
6
8
