Verona VEHOOD3610 Скачать руководство пользователя

Страница: 11 / 18

Place Recircutating Vent under cabinet and mark position of holes allowing for

unit to slide back in the keyhole slots. (1)

Drive screws into underside of cabinet leaving a

⅛

”

protrusion.

Install metal vent to underside of cabinet onto mounting screws and slide back to

rear wall. Tighten Screws.

Fasten diverter to top of hood as shown, by screwing 4 sheet metal screws

(provided) into the pre-dilled holes.

“Installation” from page 8

Drive machine screws (provided) into underside of Recirculation Kit, leaving

⅛

” protrusion.

Install hood to underside of Recirculation Lit onto mounting screws and slide

back to rear wall. Tighten Screws. Add additioal screws to back wall if

neccessary

Install Charcoal Filters to sides of blower inside Hood

Optional

Recirculation Kit *

Installation

Electrical
Opening

Optional Recirculating Kit

Purchased Separately from your Dealer

1-3.

Содержание VEHOOD3610



















Результаты поиска

Содержание VEHOOD3610

Отзывы:

Похожие инструкции для VEHOOD3610

Бренды по названию

Популярные бренды

Verona VEHOOD3610, Руководство пользователя

Результаты поиска

Содержание VEHOOD3610

Отзывы:

Похожие инструкции для VEHOOD3610

Бренды по названию

Популярные бренды