background image

16

Vermont Castings Aspen

®

 II Multi-Fuel

30003892

can fail to retain sufficient heat to enable the coal to 
combust correctly (particularly with harder grades of 
solid fuel) and can result in the fire going out during 
longer low output burns (e.g. overnight).

5. When the fire is fully established close the damper 

and set the primary air control lever to provide the 
desired output.

refuel while the coals are Still hot

Refuel the stove whilst it is still hot and there are plenty 
of glowing ashes to rekindle the fire.
Wear appropriate heat resistant protective gloves and:
1. Open the primary air control lever.
2. Open the damper.
3. Check the ash level in the pan and empty if neces-

sary.

4. Use the shaker grate to riddle the coal bed, causing 

the ash to fall through into the ash pan. (Fig. 22)

5. Add fuel, taking care not to allow fuel to overflow the 

front grate bars.

6. Close the damper and rest the primary air control as 

soon as the fire is fully reestablished.

operating the Shaker grate

1.  The shaker grate is operated by use of the multi-

function tool.

2.  Locate the hook on the multi-function tool through 

the hole in the shaker bar. (Fig. 22)

3.  Move the shaker bar in a front to back motion to 

shake free any ash deposited on the grate bars.

ash disposal

Remove ash before it reaches the top of the ash pan. 
Check the level at least once a day, and before each 
refuelling. If the ash level is close to the top of the pan, 
empty the ash pan as described below: Failure to do 
this will result in premature failure of the shaker bars 
due to excessive temperatures caused by ash build up.

cautioN:

 Wear suitable heat resistant protective 

gloves.
1.  Open the damper.
2.  Fully open the front doors.
3.  Using the slicer, pull the ash pan fully out of the 

stove, the slicer locates under the lip in the front of 
the ash pan. This provides a secure location and 
allows the slicer to act as a handle for the ash pan. 
(Fig. 23)

4. Remove the ash pan and dispose of the ashes safely
5. Replace the ash pan in the stove.
Ash should be stored outside in a metal container with 
a tight fitting lid, away from any combustible material 
until fully cool. 

it is essential to ensure that any ash 

is fully cooled before final disposal.

Pure wood ash can be composted and used as a 
garden fertiliser. Coal and solid fuel ash, or mixed ash 
should be disposed of with domestic refuse.

34
SHAKERGRATE

Shaker Bar

Multi-function Tool

ST884

fig. 22

  Attach the multi-function tool to the shaker bar.  Move 

the shaker bar forwards and backwards.

ST265

ash pan

12/99

ST265

fig. 23 

 Primary air outlet - keep clear of ash and charcoal 

accumulation.

Ash Pan

Содержание Aspen II 1405C





























Отзывы: