Vermont Castings 36CFDV Скачать руководство пользователя страница 3

CFDV Series Gas Fireplace

20305832

3

3. For 

propane/LP 

fi replace, do not place propane/LP 

supply tank(s) inside any structure. Locate propane/LP 
supply tank(s) outdoors. To prevent performance prob-
lems, do not use propane/LP fuel tank of less than 100 
lbs. capacity. 

4.  If you smell gas:

 

Shut off gas supply.

• 

Do not try to light any appliance.

• 

Do not touch any electrical switch; do not use any 
phone in your building .

• 

Immediately call your gas supplier from a neighbor’s 
phone. Follow the gas supplier’s instructions.

5.  Never install the fi replace:

• 

In a recreational vehicle

 

Where curtains, furniture, clothing, or other fl am-
mable objects are less than 36" from the front, top, 
or sides of the fi replace

 

In high traffi c areas

 

In windy or drafty areas 

6. 

Due to high temperatures, the appliance should be 
located out of traffi c and away from furniture and 
draperies.

7. This 

fi replace reaches high temperatures. 

Children 

and adults should be alerted to the hazards of high 
surface temperature and should stay away to avoid 
burns or clothing ignition.

 Fireplace will remain hot 

for a time after shutdown. Allow surfaces to cool before 
touching. 

8. 

Young children should be carefully supervised 
when they are in the same room as the appliance. 
Toddlers, young children and others may be sus-
ceptible to accidental contact burns. A physical 
barrier is recommended if there are at risk individu-
als in the house. To restrict access to a fi replace 
or stove, install an adjustable safety gate to keep 
toddlers, young children and other at risk individu-
als out of the room and away from hot surfaces.

 

9. 

Clothing or other fl ammable material should not be 
placed on or near the appliance.

10. When the appliance is installed directly on carpeting, 

tile or other combustible material other than wood fl oor-
ing, you must set appliance on a metal or wood panel 
or hearth pad extending the full width and depth of the 
appliance.

11.  Do not modify fi replace under any circumstances. Any 

parts removed for servicing must be replaced prior to 
operating fi replace. 

12. Turn fi replace off and let cool before servicing, install-

ing, or repairing. Only a qualifi ed service person should 
install, service, or repair the fi replace. Have burner 
system inspected annually by a qualified service 
person. 

IMPORTANT SAFETY INFORMATION

This fi replace is a vented product. This fi replace must be 
properly installed by a qualifi ed service person. The glass 
door must be properly seated and sealed. If this unit is not 
properly installed by a qualifi ed service person with glass 
door properly seated and sealed, combustion leakage can 
occur. 

CARBON MONOXIDE POISONING:

 Early signs of carbon 

monoxide poisoning are similar to the fl u with headaches, 
dizziness and/or nausea. If you have these signs, the fi re-
place may not have been installed properly. Get fresh air 
at once! Have the fi replace inspected and serviced by a 
qualifi ed service person. Some people are more affected 
by carbon monoxide than others. These include pregnant 
women, people with heart or lung disease or anemia, 
those under the infl uence of alcohol, and those at high 
altitudes. 

Propane/LP gas and natural gas are both odorless. An 
odor-making agent is added to each of these gases. The 
odor helps you detect a gas leak. However, the odor added 
to these gases can fade. Gas may be present even though 
no odor exists.

Make certain you read and understand all warnings. Keep 
this manual for reference. It is your guide to safe and proper 
operation of this fi replace.

1. 

Installation and repair should be done by a qualifi ed 
service person. The appliance should be inspected 
before use and at least annually by a professional 
service person. More frequent cleaning may be 
required due to excessive lint from carpeting, 
bedding material, et cetera. It is imperative that 
control compartments, burners and circulating air 
passageways of the appliance be kept clean.

2.  This appliance is only for use with the type of gas 

indicated on the rating plate. This appliance is not 
convertible for use with other gases unless a certifi ed 
kit is used. 

INSTALLER

Please leave these instructions with the appliance.

OWNER

Please retain these instructions for future reference.

• 

Read this owner’s manual carefully and 
completely before trying to assemble, operate, 
or service this fi replace. 

•  Any change to this fi replace or its controls can 

be dangerous.

•  Improper installation or use of this fi replace 

can cause serious injury or death from fi re, 
burns, explosions, electrical shock and carbon 
monoxide poisoning.

W

ARNING

Содержание 36CFDV





























































Отзывы: