Vermeer 504 PRO Скачать руководство пользователя страница 66

Страница: 66 / 153

504PRO_604PRO_o-m2_00

504/604 PRO Baler

Preparing the Equipment Baler 7-3

4. Insert the safety bolt.

5. Position the tongue jack under the draw bar of the baler.

6. Turn the crank until the tongue jack is extended.

Remove the support foot:

1. Turn the crank (1) until the support foot (4) has retracted and there is sufficient free space.

2. Remove the safety bolt (3) from the support foot holder (2).

3. Manually slide the support foot completely in the support foot holder.

4. Install the safety bolt into the support foot holder.

7.2

Adjust the Height of the Drawbar

WARNING:

Ensure maximum baler hitch weight does not exceed the permissible load on tractor drawbar(see page 13-1).

WARNING:

Death or serious chrushing injury can result if machine falls. securely support machine with suitable blocking

or jackstands. Never work under machine supported only by a jack or other lifting device.

1. Place the baler on a clean and level floor on the tongue jack(see page 7-1) and block the wheels.

2. Lower the tongue jack until the baler is in a horizontal position, the baler is horizontal when the platform is horizontal. Make sure the tongue

jack is vertical and the axle plates are in a horizontal position.

3. Remove the bolts (1) (see Figure 27 on page 7-6) and the locking plates (3) from both sides of the baler.

4. Support the drawbar front end with suitable lifting device with a lifting capacity of > 150 kg.

5. Loosen the bolts (2) from both sides of the baler.

6. Use the lifting device to lift the draw bar to the required height, the draw bar must be aligned with the hitch pin of the tractor.

7. Tighten the bolts (2) finger tight on both sides and make sure serrations are alligned on the flange plates (5).

8. Tighten the bolts (2) with the correct torque on both sides of the baler.

9. Install the locking plates with the bolts (1) on both sides of the baler.

10.Loosen the bolts (9).

https://tractormanualz.com

Содержание 504 PRO


























































































































































Результаты поиска

Содержание 504 PRO

Отзывы:

Бренды по названию

Популярные бренды

Vermeer 504 PRO, Руководство оператора и по техническому обслуживанию

Результаты поиска

Содержание 504 PRO

Отзывы:

Бренды по названию

Популярные бренды