manualshive.com logo in svg

Vermeer 504 PRO, Руководство оператора и по техническому обслуживанию

Поделиться
Скачать
Vermeer 504 PRO Скачать руководство пользователя страница 35

504PRO_604PRO_o-m2_00

-

504/604 PRO Baler

Overview of the Machine 4-1

4

OVERVIEW OF THE MACHINE

4.1

Overview of the machine

The baler has a wide pick-up max. 7.9 ft (2.40 m) and can produce round bales with a width of 4.0 ft (1.23 m) and a diameter from:

•

504 PRO 3.3

–

5.2 ft (1.00

–

1.60 m).

•

604 PRO 3.3

–

5.9 ft (1.00

–

1.80 m).

The baler produces a round bale in 5 steps:

1. Pick up the loose crop material with the Pick-Up unit.

2. Cut (if necessary) and transport the material into the compressing chamber.

3. Compress the material and form the bale.

4. Tie the bale.

5. Open the tailgate and eject the bale.

The steps 1 - 3 are continuous when the tractor drives. The tractor must stop when the tying starts in step 4. The tractor and baler must stand still
to eject the bale in step 5.

https://tractormanualz.com

Содержание 504 PRO


























































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды