Vermeer 504 PRO Скачать руководство пользователя страница 111

Страница: 111 / 153

504PRO_604PRO_o-m2_00

9-8 Operating the Machine Baler

504/604 PRO Baler

9.7.1

Open and close tailgate

The tailgate is opened and closed by means of the tractor's hydraulic control (distribution valve for the tailgate):

Tailgate must be properly closed:

•

Before beginning to pick up the crop material.

•

After each bale ejection.

To properly close and lock tailgate, move the tractor's hydraulic control to "float". This accomplishes the following:

•

Ensures tailgate fully closes while minimizing wear on tractor hydraulic pump.

•

Allows sufficient time for locking hook [1] to engage locking bolt (see Figure 66 on page 9-9)

•

Allows the net knife reset cylinder to fully retract in preparation for the next wrapping cycle.

•

Allows operator to concentrate on other tasks (i.e. tractor gear selection) while tailgate closes.

Keep the hydraulic control in "float" during baling.

A short signal tone indicates to the tractor driver that the tailgate is closed completely. Furthermore a closed tailgate is displayed on the display.

https://tractormanualz.com

Содержание 504 PRO


























































































































































Результаты поиска

Содержание 504 PRO

Отзывы:

Бренды по названию

Популярные бренды

Vermeer 504 PRO, Руководство оператора и по техническому обслуживанию

Результаты поиска

Содержание 504 PRO

Отзывы:

Бренды по названию

Популярные бренды