VERITAS D595 Скачать руководство пользователя страница 5

Страница: 5 / 5

Veritas Tools Inc. Ottawa ON K2H 1C2 Canada veritastools.com

638 INS-374_H

Care and Maintenance

The body of this plane is ductile cast iron and comes treated with rust preventative.
Remove this using a rag dampened with mineral spirits. Clean all machined surfaces.

We recommend that you initially, then periodically, apply a light coat of silicone-free
paste wax to seal out moisture and prevent rusting (as well as act as a lubricant for
smoother planing). Wipe off any wood dust from the surfaces that you will be waxing,
apply a light wax coating, let dry, then buff with a clean soft cloth. At the same time,
the solvents in the wax will remove any harmful oils left from your fingers that can
lead to corrosion.

Note: Since the face of the fence and the bottom of the depth stop will come in contact
with the workpiece, it is important to keep these parts coated with paste wax to prevent
marring the workpiece.

If storage conditions are damp or humid, the plane should, in addition to the treatment
outlined above, be wrapped in a cloth or stored in a plane sack. This precaution will
also guard against dings and scratches.

Accessories

05P45.51

A2 Blade, right

05P45.52

A2 Blade, left

05P45.55

O1 Blade, right

05P45.56

O1 Blade, left

05P45.71

PM-V11

Blade, right

05P45.72

PM-V11

Blade, left

05P45.60

Optional Long Fence Rods, pr.

05N35.11

Replacement Scoring Blade

Содержание D595






Результаты поиска

Содержание D595

Отзывы:

Бренды по названию

Популярные бренды

VERITAS D595, Быстрый старт

Результаты поиска

Содержание D595

Отзывы:

Бренды по названию

Популярные бренды