Veris DC Current Transducer (CT) Connection Instructions
For use with HOBO
®
H22, U12, U30, and UX120-006M data loggers and HOBO data nodes
© 2007–2013
Onset Computer Corporation.
All rights reserved. Onset, HOBO, and HOBOware are registered trademarks and FlexSmart is a trademark of Onset
Computer Corporation. Other products and brand names may be trademarks or registered trademarks of their respective owners.
11464-G MAN-VERIS-CT
Applies to this Veris CT:
Onset Part No.
Current Range
Output
Veris Part No.
T-VER-H970-200
0-200 Amps DC
4-20mA (or 0-5VDC) representing 0 to 50/100/200 Amps DC
H970HCA
DANGER!
—HIGH VOLTAGE HAZARD
Installing CT in an energized electrical enclosure or on any energized conductor can result in severe injury or death. This CT is for
installation by qualified personnel only. To avoid electrical shock, do not perform any installation or servicing of this CT unless you
are qualified to do so. Disconnect and lock-out all power sources during installation and servicing. Please read transducer user’s
manual for instructions and use.
This document provides instructions on connecting the Veris CT listed above to each of the
following:
•
FlexSmart
™
Analog Module used with HOBO H22 series data loggers
•
Analog Sensor Port used with HOBO U30 series data loggers
•
4-20mA cable or voltage adapter used with the U12 and UX120-006M data loggers and
ZW series data nodes
It also lists configuration values used by HOBOware
®
Pro software to configure the logger for CT.
Required:
•
Veris CT listed above
•
HOBO H22, U12, U30, or UX120-006M data logger, or HOBO ZW data node
•
FlexSmart Analog Module, Onset Part No: S-FS-CVIA (for H22 series); Analog Sensor Port option (for U30 series);
4-20mA cable, Onset Part No. CABLE-4-20mA or voltage adapter, Onset Part No. CABLE-ADAP5 (for U12,
UX120-006M, or ZW series)
•
HOBOware Pro Software, version 2.2.1 or higher (2.4.0 or higher for U30 series; 3.0 or higher for ZW series; 3.6 or
higher for UX120-006M)
•
Customer-supplied lengths of hook-up wire
Connecting the CT to the Analog Module or Port:
Sh
ld
S1
+
S1
-
Exc
+
E
xc-
S2
+
S2
-
4-
20m
A
0-
5V
D
C
G
nd
(-)
Po
we
r (
+
)
FlexSmart Analog Module
DC Current Transducer
HOBO H22 Series Data Logger
S-FS-CVIA
FlexSmart Analog Module
DC Current Transducer
DC
LOAD
*
The applicable output terminal f
rom the
CT is shown connected to the channel 2 input terminal (S2+) on the FlexSmart Analog Module.
If available, the channel 1 input terminal (S1+) can be used instead.
Sh
ld
S1
+
S1
-
Exc+
E
xc-
S2
+
S2
-
FlexSmart Analog Module
4-
20m
A
0-
5V
D
C
G
nd
(-)
Po
we
r (
+
)
for
4-20mA
Output*
for
0-5VDC
Output*
DC Current Transducer
All wiring
customer-supplied
H22 Connection
Veris DC Current
Transducer
Distributed by MicroDAQ.com, Ltd. www.MicroDAQ.com (603) 746-5524
