VERDER CARBOLITE GERO HRF 7/112 Скачать руководство пользователя | Manualshive

Страница: 20 / 28

background image

7.0 Repairs and Replacements

l

avoid damaging the grooved fibre carriers in which the elements sit; these carriers
are fragile.

7.7

Fuse Replacement

Fuses are marked on the wiring diagram with type codes, e.g. F1, F2. For more
information on fuses refer to section 10.0.

Depending on model and voltage, the different fuse types may or may not be fitted.

If any fuse has failed, it is advisable for an electrician to check the internal circuits.

Replace any failed fuses with the correct type. For safety reasons do not fit larger
capacity fuses without first consulting Carbolite Gero.

The fuses are located at the cable entry point. Remove the back panel or control box
back panel to gain access to the fuses.

20

«
...
18
19
20
21
22
...
»

Содержание CARBOLITE GERO HRF 7/112





























Отзывы:

Нет отзывов

Похожие инструкции для CARBOLITE GERO HRF 7/112

Бренд: ICP Страницы: 63

Бренд: Nagas Страницы: 49

Бренд: York Страницы: 44

Luna HT Residential series

Бренд: Baxi Страницы: 8

CARBOLITE GERO HRF 7/324

Бренд: VERDER Страницы: 28

CARBOLITE GERO HST 12/600

Бренд: VERDER Страницы: 38

CARBOLITE GERO HST 12/450

Бренд: VERDER Страницы: 38

CARBOLITE GERO GPC 13/131

Бренд: VERDER Страницы: 36

Carbolite Gero EVC 12/450B

Бренд: VERDER Страницы: 38

CARBOLITE GERO CWF-BAL 11/21

Бренд: VERDER Страницы: 38

Бренд: Carrier Страницы: 12

Бренд: Trane Страницы: 44

Бренд: Coleman Страницы: 8

Бренд: Coleman Страницы: 14

Бренд: Coleman Страницы: 28

Бренд: Ugin Страницы: 20

F9MVE A3 Series

Бренд: International comfort products Страницы: 55

Бренд: International comfort products Страницы: 59

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды