Verbatim 2-Disk RAID USB and eSATA External Hard Drive Скачать руководство пользователя страница 8

8

RAID 0

 

(Also called Striping) distributes data across both disks in a way which 
can improve throughput, while retaining full capacity. However, in case 
of possible failure of either disk, all data will be lost and the array will 
no longer mount to your computer. Available capacity is the combined 
capacity of both drives.

If either disk fails in RAID 0 then the LED of the failed drive will change 
to RED.

RAID 1

 

(Also called Mirroring) stores a duplicate set of data onto both disks, so that 
if one disk fails all data can be recovered from the other disk. 
Available capacity is equal to that of only one of the two included drives.

If either disk fails in RAID 1, then the LED corresponding to the failed disk 
will change to RED. The remaining operational disk can continue to be used 
until the failed disk has been replaced. However, in this instance there is no 
longer any data protection provided by the second, failed drive.

If you have been using RAID 1 mode and there is a subsequent failure of 
either of the two drives, you can disassemble the enclosure and replace 
the failed drive with a new drive. After reassembling the enclosure, leave it 
disconnected from your computer and power it up. When the new drive is 
detected during the power-on sequence, the full data of the original drive 
will be rebuilt onto the new drive. This rebuilding procedure can take many 
hours (more than 5!) to complete. During the rebuilding procedure, the 
LED of the original good drive will fl ash BLUE, while the LED of the new 
replacement drive will fl ash RED. After the array has rebuilt successfully 
both LEDs will change to BLUE.

Concatenation

 

(RAID Mode Switch Setting = “BIG”) combines both physical disk drives 
into a single virtual disk. Available capacity is the combined capacity of 
both drives.

This mode provides no data redundancy. If either disk fails in Concatenation 
mode, then the array will no longer mount to your computer.

If either disk fails in Concatenation mode, then the LED corresponding to 
the failed disk will change to RED.

Содержание 2-Disk RAID USB and eSATA External Hard Drive
















Отзывы: