Total number of tracks
Begin to play the first track
811-830191-210
PRINTED IN CHINA
Pause mode of the 1st track
TROUBLE SHOOTING GUIDE
Should any problem persist after you have made the following checks, consult your nearest service
facility.
DISC PLAY DOES NOT START:
•
The disc is inserted upside down or incorrectly. Insert the disc correctly with the label surface
up
•
Dusty or defective disc
•
Dirty or dusty lens
•
The disc compartment lid is not closed
•
Moisture condensation-> leave the unit in a warm place until the moisture evaporates
•
The AC power adaptor is not plugged into the wall outlet
•
The unit is not placed on a level surface
•
Weak batteries
NO SOUND FROM THE HEADSETS:
•
The headphones / earphones plug is not firmly connected to the “PHONES” jack.
•
Adjust the volume control
•
Dirty plug
SKIPPING OF SOUND:
•
Dirty or defective disc
•
Dirty lens
•
Strong vibration
WHEN USING WITH BATTERIES THE BATTERY LIFE IS SHORT:
•
Use alkaline batteries and not manganese batteries.
DISPLAY WINDOW SHOWS “
” ERROR MESSAGE AND THE UNIT CANNOT BE OPERATED:
•
No disc, dirty or scratched disc. The unit will return to power off after approx. 30 seconds, or
reset the player by pressing “ ” button once and then insert a disc to start playing.
SPECIFICATIONS
GENERAL
OUTPUT (at 1KHz 0dB level): Headphones / earphones (stereo mini-jack)
15 mW+15mW at 16 Ohms to 32 Ohms
POWER REQUIREMENTS:
3V (2 x AA / LR6 / MN 1500) alkalline batteries,or
DC IN 6V, 350mA power adaptor
Polarity of plug
OPERATING VOLTAGE:
We continually strive to improve our products, specifications may change without notice.
DISC PLAYING
1. Open the CD door by pressing the “
” button.
2. Place a CD with the label side facing upwards onto the centre spindle, gently push down until
the disc clicks in place.
3. Press the top of the CD door to close.
ON DISPLAY WINDOWS
If a CD is loaded, when you press “
” button, the display window shows:
DURING PLAYING
The track number of the current selection appears.
When “ ” is pressed during play, total number of tracks on the disc will be displayed and the unit will stop
playing.
If “ ” is pressed again, the unit will return to full stop mode. If “
” is pressed, the unit will return to
play mode.
Note: When “ ” is pressed once during play, the unit will return to full stop mode automatically if no button
is pressed again within 30 seconds. Or press “ ” for a few seconds to stop the unit.
DURING PAUSE
The playing track number will flash.
When no disc is inserted and “
” button is pressed, “ ” will be shown on the display.
The unit cannot be operated when error message is displayed. After approx. 30 seconds the unit
will return to full stop mode. Reset the player by pressing “ ”once and then insert a disc to start
playing.
VARIOUS PLAYING MODES
During playback, every time the “ PLAY MODE ” button is pressed, the playing mode will be
changed as follows:
IN NORMAL PLAYING MODE:
NORMAL PLAY -> (
) REPEAT ONE -> (
) REPEAT ALL -> INTRO -> SHUFFLE
NORMAL PLAY-- Playing the whole disc
The CD is played once from the beginning to the end.
REPEAT PLAYBACK-- Repeat One and Repeat All
•
To repeat single track
Press “ PLAY MODE ” button during play until “
” appears on the
display. The selected track will be played repeatedly.
To select another track, press “
”or “
” button.
•
To repeat whole disc
Press “ PLAY MODE ” button during play until “
” appears on the
display.
The whole disc will be played repeatedly.
INTRO PLAY-- Playing the first ten seconds of all the tracks
1. Press “ PLAY MODE ” button during play until “ INTRO ” flashes on the
display.
2. Press “
” button to begin “ INTRO ” play.
Each track will be played about ten seconds.
3. Pressing “
” button again will cease intro play and continue to normal playback.
NOTE: Intro play always starts from the first track.
SHUFFLE PLAY--playing the tracks in random order
1. Press “ PLAY MODE ” button during play until “ SHUFF ” flashes on the display.
2. Press “
” button to begin the shuffle play.
•
To locate the next track, press “
” button.
NOTE: You cannot locate the previous track even you keep the “
” button
pressed.
PROGRAM PLAY-- playing the tracks in the desired order
1. Press “ PROG ” button until “ PROG ” and “
” flash on the display.
2. Press “
” or “
” button to select the desired track.
3. Press “ PROG ” button to register track. For example, No. 6 as the first selection.
The track No. indication will return to “
”.
4. Repeat steps 2 to 3, until all the desired tracks are programmed ( up to 20
tracks).
5. Press “
” button, and program playing begins.
NOTES:
•
Repeat play and intro play can be performed during program play. But shuffle play is inactive.
•
The program is erased, when:
1. The disc compartment is opened or the auto power off function turns the power off.
2. If the “ ” is pressed twice, then the stored program will be erased.
•
When “ ” is pressed once,the program will still remain in the memory before auto power off.
PROGRAM EDITION
To add:
To add additional tracks to your selection during program playback, press “ ” button
first and then press “ PROG ” button repeatedly until “
” flashes in the display. Repeat the
above steps 2 and 3 to store additional tracks.
To check:
Press “ PROG ” button during programming before you press “
” button.
Each time “ PROG ” button is pressed a previously stored track number appears in the
display.
To change: When checking press either skip button to alter the track number for the program
currently displayed. Press “ PROG ” button to register the newly selected track into memory.
To delete:
Opening the CD door will result in any programmed memory being deleted.
SKIP PROTECTION SYSTEM
The SKIP PROTECTION system incorporates a special electronic circuit that prevents sound from
skipping when the unit is subject to shocks and vibration during playing.
When you start playback, the SKIP PROTECTION system turns on and “
” indicator flashes in
the display. The unit starts to read the music data into a buffer memory to prevent the sound from
skipping. When the memory buffer is full the “
” indicator will stop flashing.
When the unit receives a physical shock which prevents the laser pick-up from “ reading ” the CD,
the system immediately starts playing the sound stored in its memory and continues until the laser
pick-up recovers.
If the unit is subject to continuous shocks and all the data stored in memory is used up the sound will skip.
If the vibration stops then the data memory will be restored. If continuous vibration is applied when the data
memory is empty, an error message “
” will be displayed. To reset the CD player press “ ” button
once.
MAINTENANCE
CLEANING THE UNIT
Do not use volatile chemicals on this unit. Clean by lightly wiping with a soft cloth.
CLEANING A CD
If the CD skips or will not play, the disc may need to be cleaned.
Before playing, wipe the disc from its centre to its outer edge with a soft cleaning cloth. After
playing, store the disc in its case.
HANDLING THE DISC
Only touch the CD on the outer edge to avoid leaving finger prints on its surface.
Do not stick paper or tape or write anything on the surface of the CD.
U.S.A., Canada: 120V AC ±5% 60Hz
