LAUTUS/2020/V2
12/20 tel. +48 (22) 751 95 50 www.venture.pl fax. +48 (22) 751 22 59
tel. (22) 751 95 50 www.venture.pl fax. (22) 751 22 59
ENGLISH (Translation)
INTRODUCTION
This manual covers fans in standard version, listed on the title page (In the case of the fan special version the manual may be
different from this document). It is source of information necessary for safe and proper use. Read this manual carefully before
any use of the device, comply with its requirements and keep it in place with easy access for users and service. If case of any
doubts about use of the fan, please contact with manufacturer.
After receiving the device - check:
whether the device is in compliance with order,
whether the data on the rating plate are the same as desidered (voltage, frequency, etc.)
whether fan was not damaged during transport (e.g. there are no dents/cracks, impeller rotates freely)
In case of any irregularities, contact with your dealer or Venture Industries Sp. z o.o. service.
1. GENERAL INFORMATION
1.1 Information about device
The device is intended for domestic use or use in an industrial environment. It is allowed to use and operate the device only by adults who
have read this manual or have been properly trained.
The device is designed to transport and purify the air from dust and microorganisms. It is forbidden to transport explosive gases, solids,
liquids, abrasive substances, and chemically aggressive compounds. The device is designed for indoor use at an ambient temperature of 10 ° C
to 40 ° C
The purifier should be protected against the influence of weather conditions (eg snow, rain, excessive sunlight, lightning). The device is not
intended for outdoor use. The camera environment cannot contain explosive mixtures, abrasive substances, chemically aggressive substances,
viscous substances, liquids, substances with high humidity. The device must not be exposed to radiation (e.g. microwave, ultraviolet, laser,
x-ray).
• A description of the structure of the device is presented in Annex C.
• Additional information on the use of the device is provided on the housing in the form of stickers. More information is provided in Annex A.
1.2 General risk and guidelines
During entire air purifier life cycle pay particular attention to the risk and guidelines presented below:
1.2.1 Mechanical risk and guidelines
The device has moving parts (eg fan impeller), contact with which may cause serious injury. Do not use the device if the
service cover is open and a set of filters have not been closed.
After being disconnected from the power supply, the fan wheel may rotate for some time. The cover of the device can be
removed after the rotor has stopped completely. To do this, with extreme caution, check with your hand that there is air flow
at the outlet of the fan.
1.2.2 Suction power
Pay particular attention to the fact that there are no small elements or dust deposits near the inlet, as their suction may cause quick clogging
of the filters and even their damage.
1.2.3 Thrown items
Before the first start-up and after the device was opened (eg service work), check that the inside of the device does not contain foreign
elements (eg tools) that could damage the device or be thrown outside. Regularly check the condition of the appliance outlet covers.
1.2.4 Sharp edges
At the production stage, sharp edges of the device casing are softened, however, it may have edges, touching which may
cause injury, especially inside the device. It is recommended to wear protective gloves when servicing the equipment.
1.2.5 Risk and guidelines related with noise
The operating device produces noise. The value of the sound pressure level generated by the device is available at
www.venture.pl.
1.2.6 Materials
In the event of fire or transport of an inappropriate medium - fan elements may generate vapours hazardous to health.
1.2.7 Risk and guidelines related with electricity
Do not perform any work on the device (eg. installation, use, maintenance and inspection, dissambly) with exposed parts that
may be under voltage. Capacitor (only in units with single phase supply) has accumulated charge even after disconnecting the
unit. The appropriate steps should be made to prevent from electric shock. Protect from getting access to the electric elements
by unauthorized person.
Do not put the device on a wet surface, spray it with water or touch it with wet hands, as this may result in electric shock.
Do not use the device if the power cord is damaged. Before connecting to the power supply, check that the power cord is not damaged, and if
damaged, replace it.
1.2.8 Maintenance
Incorrect installation and operation may lead to damage to the device and a dangerous situation. The operation of the device may be carried
out by persons acquainted with the manual or properly trained.
Any modifications to the device are not allowed. Complicated maintenance works, e.g. requiring disassembly of the rotor, HEPA filters or
control systems, should be performed each time by the SERVICE of Venture Industries Sp. z o.o. or outside the service - after obtaining the
manufacturer's consent, according to additional guidelines. Incorrect assembly may deteriorate the operating parameters, damage the device,
and lead to a hazardous situation.
