Ventrac KX523 Скачать руководство пользователя страница 15

Страница: 15 / 49

Operation - 15

Operational Control Locations

Use the following images to help identify the locations

of operational controls. The letter next to each control

can be referenced to the list that follows these images.

A. Discharge Chute Rotation

(Secondary S.D.L.A. Lever)

B. Discharge Chute Adjustment Link

Optional Discharge Chute Deflector

Actuator Control

Discharge Chute Rotation (A)

(Secondary S.D.L.A. Lever)

The secondary S.D.L.A. lever on the power unit con-

trols the hydraulic rotation of the discharge chute.

The discharge chute can be angled from left to right

(180 degrees of rotation) to discharge snow in the

desired direction.

Discharge Chute Adjustment Link (B)

The discharge chute adjustment link controls the

angle of the discharge chute deflector. The angle of

the discharge chute deflector determines the dis

tance that snow is thrown.

Optional Discharge Chute Deflector

Actuator Control (C)

This optional actuator replaces the discharge chute

adjustment link on the snow blower. It couples with

a 12 volt switch on the power unit, allowing the

operator to control the angle of the discharge chute

deflector from the operator’s seat.

The actuator

is controlled

with an

optional dash

mounted

momentary

on toggle

switch (D) on

KT4100 and

KT4200

models.

The actuator is

controlled by

momentary on

switches (E) on the

optional 12V front

SDLA handle on

KN4500 models.

OPERATIONAL CONTROLS

Содержание KX523


















































Результаты поиска

Содержание KX523

Отзывы:

Похожие инструкции для KX523

Бренды по названию

Популярные бренды

Ventrac KX523, Руководство оператора

Результаты поиска

Содержание KX523

Отзывы:

Похожие инструкции для KX523

Бренды по названию

Популярные бренды