www.venton.de
INSTRUCTION MANUAL
Seite 2
FEATURES OF THIS PRODUCT
PRODUCT ASSEMBLY
ASSEMBLE OF BASE
Set the column in place on the base and secure it
using the "L" screw with washer while also
engaging the counterweight.
Make sure column and base and counterweight are
firmly coupled.
Loosen the Height Adjustment Collar on top of the
Inner Tube. Pull the Inner Tube out from the Outer
Tube to adjust the tube to the desired height and
tighten the collar.
If necessary, slightly loosen the Set Screw by turning
it anticlockwise. Slide the Switch Box down over the
Inner Tube and tighten the Set Screw. Make sure the
Set Screw is tightly secured.
ASSEMBLE OF BLADE AND GRILLE
Unscr0ew the plastic mounting nut from the front of
the motor housing by rotating it anticlockwise.
Position the rear grille against the front of the motor
housing with the handle uppermost, ensuing that the
locating pegs on the motor housing are engaged
correctly in the holes of the rear grille.
Tighten the Rear Grille Mounting Nut clockwise.
DO
NOT OVERTIGHTEN IT
.
Push the fan blade onto the motor shaft, locating the
slot at the back of the blade on the drive pin that
passes through the motor shaft.
Tighten the blade cap by turning it anticlockwise.
Position the front grille against the rear grille so that
the holes in the rims that accept the small nut and bolt
are in line. Insert the bolt through the holes and screw
on the nut. Do not fully tighten at the stage.
Push the grille retaining clips into position ensuring
that they engage correctly on the rim of the grille.
Fully tighten the small nut and bolt that passes
through the rim of the grille.
OPERATION OF THE PRODUCT
Control Panel
，
SPEED SETTING
Button 0-1-2-3
1. To change speed, press button “1” – “2” – “3”.
Speed will
change with each button stroke.
2. For oscillation, press the oscillation knob which
located in the motor housing, the fan starts oscillating.
To stop oscillation, pull up the oscillation knob.
3. To switch the fan off, press the button “0”.
4. Always unplug the appliance when it is not used.
CLEANING
Switch off and unplug from the power supply before assembling or disassembling and cleaning.
Keep the air vents at the rear of the main body free from dust or fluff– use a vacuum cleaner to remove these when necessary. Do not probe
any opening to remove fluff.
Fan component parts should be cleaned using mild soap and a damp cloth or sponge. Do not allow any water or other liquid to enter the
motor housing.
Thoroughly remove soap film with clean water.
CAUTION: Do not use harsh detergents, chemical cleaners or solvents as they may damage the surface finish of the fan
components.
The CE marking confirms the conformity and compliance with all relevant EU directives and regulations (EMV / EMC, ErP, EuP, RoHS, REACH, BauPVO), in particular the
requirements according to the EU product standards, low voltage directive and safety requirements according to EN 50083 -2,
2014/30/EU (EMV), 2014/35/EU (LVD), 2011/65/EU
(RoHS), good class All test reports and certificates are available.
Notice of participation in the Landbell AG exemption system
"With regard to the sales packaging filled by us for the first time and given to private end consumers, our company has joined the nationwide take-back system of Landbell AG,
Mainz, (customer number: 4104375) to ensure the fulfillment of our legal obligations in accordance with Section 6 of the Packaging Ordinance You can find information on the
website of Landbell AG. "
WEEE Waste of Electrical and Electronic Equipment - Disposal of old devices Electronic devices do not belong in the household waste, but must - in accordance with the directive
DIN EN 50419 (corresponds to Article 11 (2) of the directive 2002/96 / EG - 2012/19 / EU of the European Parliament and of the Council of January 27, 2003 on electrical and
electronic equipment - WEEE Reg.No. 76454326. Please return this device for disposal at the end of its use for disposal
This product complies with the European Directive 2012/19 / EU on waste electrical and electronic equipment (WEEE), which defines the legal framework applicable in the
European Union for the disposal and recycling of electrical and electronic equipment. Do not throw this product in the trash. Take it to the nearest electrical and electronic waste
treatment facility.
All brands and logos mentioned are registered and enjoy property rights by their owners. www.venton.de