background image

HEAT/COOL DIFFERENTIAL - The Heat and Cool setpoints will not be 
    allowed to come any closer to each other than the value set in Advanced 
    Setup 

step #7, on page 13

.  This minimum difference is enforced during 

    Auto-changeover and Program On operation.

    

Note:

  To increase the spread between the heating and cooling setpoints, 

    press the MODE button until only the heat setpoint is displayed; adjust to 
    the desired setpoint.  Press the MODE button until only the cool setpoint 
    is displayed; adjust to the desired setpoint.  Press the MODE button again 
    to enter the Auto-changeover mode where both the heat and cool 
    setpoints are displayed.

         
        

About Advanced Features & Operation

WARNING: This will reset all Time Period and Advanced Programming to 
the  default  settings.   Any  information  entered  prior  to  this  reset  will  be 
permanently lost.

FACTORY DEFAULTS - 
    settings back to the factory default settings, follow the instructions below.  

If, for any reason, you desire to return all the stored

After all of the icons appear, release 
the MODE and 
DOWN buttons.  
Then press and 
hold the FAN 
button for 5 seconds.

After the letters 

Fd

 appear on the 

display (Factory 
Default), release 
the FAN button.  
Press the MODE
button 

twice

 to return to normal 

operation.  Two dashes will appear
momentarily as the display resets.

FAN

Press

Press

MODE

MEMORY BACKUP - In the event of a power loss, the thermostat will retain 
    the stored program settings without external power or batteries.
       

PROGRAMMABLE FAN - 
    and the fan will run for the number of minutes selected in step #10 
    on page 14.  

This timer will start the fan at the top of each hour;

Page 17

Press 

button.

While holding the 
MODE button, 
press and hold 
the DOWN button 
for 5 seconds.  
All of the icons will appear on 
the display.

and hold the MODE 

Place the 
thermostat in 
the OFF mode.

Press

MODE

Press

MODE

88

88

H

EAT

C

OOL

OFF

AUTO

Fan On

Program

Locked

Setup

On

o

o

Am

Pm

I8 88

88

:

Day

Night

Evening

Morning

SuMTuWThFSa

OFF

Pm

I2 00

70

:

Su

OFF

Pm

I2 00

70

:

Su

Содержание T1100RF























Отзывы: