background image

Warranty

One-Year Warranty - This Product is warranted to be free from defects in material and workmanship.  If it 
appears within one year from the date of original installation, whether or not actual use begins on that 
date, that the product does not meet this warranty, a new or remanufactured part, at the 
manufacturer’s sole option to replace any defective part, will be provided without charge for the part 
itself provided the defective part is returned to the distributor through a qualified servicing dealer. 

THIS WARRANTY DOES NOT INCLUDE LABOR OR OTHER COSTS incurred for diagnosing, repairing, 
removing, installing, shipping, servicing or handling of either defective parts or replacement parts.  Such 
costs may be covered by a separate warranty provided by the installer.  

THIS WARRANTY APPLIES ONLY TO PRODUCTS IN THEIR ORIGINAL INSTALLATION LOCATION AND BECOMES 
VOID UPON REINSTALLATION.

LIMITATIONS OF WARRANTIES – ALL IMPLIED WARRANTIES (INCLUDING IMPLIED WARRANTIES OF FITNESS FOR 
A PARTICULAR PURPOSE AND MERCHANTABILITY) ARE HEREBY LIMITED IN DURATION TO THE PERIOD FOR 
WHICH THE LIMITED WARRANTY IS GIVEN.  SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN 
IMPLIED WARRANTY LASTS, SO THE ABOVE MAY NOT APPLY TO YOU.  THE EXPRESSED WARRANTIES MADE IN 
THIS WARRANTY ARE EXCLUSIVE AND MAY NOT BE ALTERED, ENLARGED, OR CHANGED BY ANY DISTRIBUTOR, 
DEALER, OR OTHER PERSON WHATSOEVER.

ALL WORK UNDER THE TERMS OF THIS WARRANTY SHALL BE PERFORMED DURING NORMAL WORKING 
HOURS.  ALL REPLACEMENT PARTS, WHETHER NEW OR REMANUFACTURED, ASSUME AS THEIR WARRANTY 
PERIOD ONLY THE REMAINING TIME PERIOD OF THIS WARRANTY.

THE MANUFACTURER WILL NOT BE RESPONSIBLE FOR:
1.  Normal maintenance as outlined in the installation and servicing instructions or owner’s
     manual, including filter cleaning and/or replacement and lubrication.
2.  Damage or repairs required as a consequence of faulty installation, misapplication, abuse,
     improper servicing, unauthorized alteration or improper operation.
3.  Failure to start due to voltage conditions, blown fuses, open circuit breakers or other 
     damages due to the inadequacy or interruption of electrical service.
4.  Damage as a result of floods, winds, fires, lightning, accidents, corrosive environments or
     other conditions beyond the control of the Manufacturer.
5.  Parts not supplied or designated by the Manufacturer, or damages resulting from their use. 
6.  Manufacturer products installed outside the continental U.S.A., Alaska, Hawaii, and
     Canada.
7.  Electricity or fuel costs or increases in electricity or fuel costs for any reason whatsoever
     including additional or unusual use of supplemental electric heat.
8.  ANY SPECIAL INDIRECT OR CONSEQUENTIAL PROPERTY OR COMMERCIAL
     DAMAGE OF ANY NATURE WHATSOEVER.  Some states do not allow the exclusion of
     incidental or consequential damages, so the above may not apply to you. 

This warranty gives you specific legal rights and you may also have other rights which may vary from 
state to state. 

P/N 88-628  Rev. 1

C

c

F

FOR HOME OR OFFICE USE

Tested to Comply

with FCC Standards

Humidity Module            ACC0430

Page 8

Содержание ACC0430










Отзывы: