Vendors Exchange REVISION Скачать руководство пользователя страница 22

Страница: 22 / 28

INSTALLATION GUIDE

REVISION™ Door for National 157/167 - 158/168

INSTALL DROP SENSOR

First, remove single screw on hinge side of bucket

Then, mount drop sensor kit

(see page 7)

to stud and fasten

#8-32 Kep

Nut (VE7207K)

to bracket on drop sensor.

Next, apply Reflective Tape to opposite side of the Vend

Bucket, positioning the tape as close as possible to rear edge

of the bucket.

Then, punch screws through reflective tape holding new

Deflector (VE9314)

as shown.

Next, using a 1/4” nut driver, loosen

Top Plate (VE4310P)

removing nuts from top of sensor bracket and lifting off plate.

Then, connect 4-Pin harness into 4-prong plug on sensor

board

NOTE:

Remove National SureVend™ drop

sensor before installing VE drop sensor.

NOTE:

Check that drop sensor assembly

is not tilted or twisted after mounting.

NOTE:

Ensure the surface

is clean and free of debris

before applying tape.

(Continued next page)

REMO

VE OEM DOOR

INS

TALL DOOR

HARNESSING

INS

TALL BUCKET

DROP SENSOR

ADJUS

T DOOR

Stud

Top Plate

Remove (2)

Nuts

Hole

Drop Sensor

Kit

Keps Nut

Reflective Tape

Deflector

Punch Screws

Through

Stud

Drop Sensor Kit

4-Pin Harness

Sensor

Board

Overview

To TOC

Содержание REVISION





























Результаты поиска

Содержание REVISION

Отзывы:

Похожие инструкции для REVISION

Бренды по названию

Популярные бренды

Vendors Exchange REVISION, Руководство по установке

Результаты поиска

Содержание REVISION

Отзывы:

Похожие инструкции для REVISION

Бренды по названию

Популярные бренды