Velleman CAMSET5A Скачать руководство пользователя страница 3

VELLEMAN                                                                                  CAMSET5A -- VERSION II 

2

 

 

 

 

 

CAUTION 

 

RISK OF ELECTRIC SHOCK DO NOT OPEN 

 

CAUTION 

 

TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE 

COVER (OR BACK) NO USER-SERVICEABLE PARTS INSIDE. 

REFER SERVICING TO QUALIFIED SERVICE PERSONNEL

 

 

 

The lighting flash with arrowhead symbol, within and 
equilateral triangle, is intended to alert the user to the 
presence of uninsulated "dangerous voltage" within the 
product's enclosure that may be of sufficient magnitude to 
constitute a risk of electric shock to persons. 

 

The exclamation point within an equilateral triangle is 
intended to alert the user to the presence of important 
operating and maintenance (servicing) instructions in the 
literature accompanying the appliance. 

 

SAFETY INSTRUCTION 

 
Before using this unit please read these operating instructions carefully. 
Take special care to follow the warnings indicated on the unit itself as well as 
the safety suggestions listed below. Keep them handy for future reference. 
 
1.  Power source - The unit should be connected to power supply only of the 

type described in the operating instructions or as marked on the unit. 

 
2.  Water and Moisture - Do not use this unit near water. 
 
3.  Heat - Do not install the unit near heat sources such as radiators, stoves, 

heat registers, or other appliances that produce heat. 

 
4.  Ventilation - The unit should be situated so that its location or position 

does not interfere with its proper ventilation. 

 
5.  Foreign Material - Care should be taken so that objects do not fall into 

and liquids or not spilled into the unit. 

 
6.  Surface - Place the unit on a flat, level surface. 
 

Содержание CAMSET5A











Отзывы: