Velatia ORMAZABAL gae.630 Скачать руководство пользователя страница 15

Страница: 15 / 64

IG-322-EN version 03; 22/07/2022

General instructions

-insulated circuit-breaker panel:

Type

gae

.630 -1LSV(G)-/5/

in modular extensible design up to 24 kV, 20 kA

Transport and installation

3.5. Installation and assembly

To install the circuit-breaker panel, use the installation plan

shown in Chapter 3.6.1. In order to assure secure standing

of the circuit-breaker panel use all fastening bores provided.

The depths of the individual panel types in the

gae

family

vary.

In order to ensure all possible block/ panel combinations

can be installed, the foundation projection must be drawn

at a distance of 135 mm from the wall!

On the variant with pressure absorber channel the minimum

distance is 100 mm.

If it is certain that during a system extension no:
•

gae

.630 -1LSFxx- panels

•

gae

measuring panels with metal cooling stretch are

installed, the distance from the wall can be reduced

to 100 mm.

To ease the assembly of the modular switchgear

gae

.630,

we recommend the following distances from side walls on

installation from left to right:

• Distance from left wall at least 100 mm
• Right wall distance at least 300 mm.

When installing from right to left the lateral wall distances

are reversed.

The area for the floor opening must not be reduced in

size, so that, in case of an arc incident, the hot gases

can be safely discharged.

A straight and level floor surface is a prerequisite for the

stress-free installation. Pay attention to the information

in DIN 43661. In particular the tolerance on the evenness

(maximum 1 mm over a measured length of 1 m) and

the tolerance on the straightness (maximum 1 mm per

metre and maximum 2 mm over the entire length of the

foundation rail) are to be observed.

To ease the assembly work on the installation of

several

gae

panels, we recommend the usage of a

metal chassis.

The fastening material is not part of the delivery.

To fastening the switch panel to a raised floor, we

recommend the following fastening material:

• Hexagon screw M10 (minimum M8, strength class 5.6)

DIN EN ISO 4017

• Washers DIN EN ISO 7093 (switch panel side)
• Washers DIN EN ISO 7089/7090 (raised floor side) or

tapered washers for fastening to U-sections

• Spring lock ring DIN 127 / DIN 128
• Hexagon nut M10 DIN EN ISO 4032

In the case of installation on concrete with a strength of

B ≥ 25 N/mm², we recommend the following fastening

material:

•  Fischer plastic dowels of type S12
•  Wood screw DIN 571-10x80-St
•  Washer DIN 125 A10

To make the fastening bores accessible for installation,

remove the front cover (see Chapter 5) and if applicable the

cable fixing irons of cable connection compartment.

Содержание ORMAZABAL gae.630

































































Результаты поиска

Содержание ORMAZABAL gae.630

Отзывы:

Velatia ORMAZABAL gae.630, Руководство пользователя, Страница: 15 / 64

Результаты поиска

Содержание ORMAZABAL gae.630

Отзывы: