Velatia ORMAZABAL gae.630 Скачать руководство пользователя страница 13

Страница: 13 / 64

IG-322-EN version 03; 22/07/2022

General instructions

-insulated circuit-breaker panel:

Type

gae

.630 -1LSV(G)-/5/

in modular extensible design up to 24 kV, 20 kA

Transport and installation

3.3. Arrival and unpacking

The goods must be checked immediately upon receipt!
Any complaints have to be stated on the freight

document and countersigned by the driver!
In case of complaints please contact your distributor:

www.ormazabal.com

Remove the tightening straps. The circuit-breaker panel

is then no longer secured. Due to its design, the centre

of gravity of the circuit-breaker panel is higher than the

middle of the switch panel.

When handling the circuit- breaker panel in unsecured

condition the unit may tip over! Particular attention is

to be paid to this issue when transporting the circuit-

breaker panel to its place of installation. It not allowed

to use levers to transport the circuit-breaker panel to

its final position. This action could cause damage to

the enclosure.

Eyebolts are fitted to both sides of the

gae

.630 -1LSV panel,

which hold the panel safely in its position of centre of

gravity when transporting with chain or rope lifting gear

(Figure 3.2). Only transport cross members must be used

with this type of lifting gear. Otherwise there is a risk of

damage to the panel.

In some individual cases, the eyebolts are enclosed with the

panel. When fitting the eyebolts, it must be observed that

they are tightly seated and in the correct Figure 3.2 position.

37250305

Figure 3.2.

Содержание ORMAZABAL gae.630

































































Результаты поиска

Содержание ORMAZABAL gae.630

Отзывы:

Похожие инструкции для ORMAZABAL gae.630

Бренды по названию

Популярные бренды

Velatia ORMAZABAL gae.630, Руководство пользователя

Результаты поиска

Содержание ORMAZABAL gae.630

Отзывы:

Похожие инструкции для ORMAZABAL gae.630

Бренды по названию

Популярные бренды