Velatia ORMAZABAL gae.630 Скачать руководство пользователя страница 12

Страница: 12 / 64

IG-322-EN version 03; 22/07/2022

Transport and installation

General instructions

-insulated circuit-breaker panel:

Type

gae

.630 -1LSV(G)-/5/

in modular extensible design up to 24 kV, 20 kA

3. Transport and installation

3.1. Safety notes for transport

1. Lifting tackle must only be used at points

intended for this purpose.

2. Ropes, chains or other lifting tackle must be fitted

with safety hooks.

3.  Do not use any torn or worn ropes.
4.  Ropes and chains must not be knotted.
5.  Ropes and chains must not touch any sharp

edges.

6. Only use ropes and chains of sufficient loading

capacity (for weight of the circuit-breaker panel,

see Chapter "8. Technical data", "Table 8.3.").

7. Only use lifting gear of sufficient loading capacity

(for weight of the circuit-breaker panel, see

Chapter "8. Technical data", "Table 8.3.").

8. Do not lift loads over persons.

During transport, comply with the warning and

safety instructions on the circuit-breaker panel and its

packaging.

When unloading observe the safety instructions (see

Chap. 3.1) and the applicable accident prevention

regulations.

3.2. Transport and unloading

The circuit-breaker panel is delivered packed upright on

a pallet. It is fastened to the pallet with tightening straps

(Figure 3.1).

For transportation or intermediate storage, please always

use the original packaging and secure the circuit- breaker

panel with straps in the same way as for delivery.

When attaching the tightening straps make sure to attach

these as shown in Figure 3.1, as otherwise the circuit-

breaker panel may be damaged.

Import: Unloading is only allowed to be performed by

experienced persons who are fully familiar with the lifting

gear.

Observe the permissible hoisting weight of lifting tackle

and lifting gear (forklift truck, crane).

37250304

Corner protectors (cardboard)

Tightening strap

Switchgear front

Figure 3.1.

Содержание ORMAZABAL gae.630

































































Результаты поиска

Содержание ORMAZABAL gae.630

Отзывы:

Похожие инструкции для ORMAZABAL gae.630

Бренды по названию

Популярные бренды

Velatia ORMAZABAL gae.630, Руководство пользователя

Результаты поиска

Содержание ORMAZABAL gae.630

Отзывы:

Похожие инструкции для ORMAZABAL gae.630

Бренды по названию

Популярные бренды