background image

17

4 Connecting to power supply

FIBERTRAC 31 • Four-wire 4 … 20 mA/HART

62067-EN-211203

4.3  Connection - Level detection

Non-Ex instruments and instruments with non-intrinsically safe 

current output

1

1

24

/L

/N

PE

56

91

01
1

22

11

12

21

22

19

20

18
17

14
13

16
15

12

2

7

3

1

4

5

6

8

9

10

Fig. 12: Electronics and connection compartment with non-Ex instruments and 

instruments with non-intrinsically safe current output
1  Voltage supply

2  Relay output

3  Signal output 8/16 mA/HART active

4  Signal output 8/16 mA/HART Multidrop passive

5  Signal input 4 … 20 mA

6  Switching input for NPN transistor

7  Switching input floating

8  Transistor output

9  Interface for sensor-sensor communication (MGC)

10  Setting the bus address for sensor-sensor communication (MGC) 

3)

 

5 6 7 8

2

1

Fig. 13: Adjustment and connection compartment with non-Ex instruments and 

instruments with non-intrinsically safe current output
1  Terminals for the external display and adjustment unit

2  Contact pins for the display and adjustment module or interface adapter

If inductive loads or stronger currents are switched through, the gold 

plating on the relay contact surface will be permanently damaged. 

The contact is then no longer suitable for switching low-voltage 

circuits.

Electronics and con-

nection compartment 

- Non-Ex instruments and 

instruments with non-

intrinsically safe current 

output

Adjustment and con-

nection compartment 

- Non-Ex instruments and 

instruments with non-

intrinsically safe current 

output

Connection to a PLC

3)

  MGC = Multi Gauge Communication

Содержание FIBERTRAC 31





























Отзывы: