background image

6

2 Product description

FIBERTRAC 31 • Four-wire 4 … 20 mA/HART

62067-EN-211203

The level is detected contactlessly right through the vessel wall. 

Neither a process fitting nor a vessel opening are required. The instru-

ment is thus ideal for retro installation.

In radiometric measurement, a Caesium-137 or Cobalt-60 isotope 

emits focussed gamma rays that are attenuated when penetrating 

the vessel wall and the medium. The PVT detector on the opposite 

side of the tank receives the radiation, whose strength is dependent 

on the level. The measuring principle has proven to be very reliable 

in conjunction with extreme process conditions because it measures 

contactlessly from outside through the vessel wall. The measuring 

system ensures maximum safety, reliability and plant availability, 

independently of the medium and its properties.

2.3  Corresponding source container

A radioactive isotope in a suitable source holder is the prerequisite for 

a radiometric measurement setup.
The handling of radioactive substances is regulated by law. The radia-

tion protection rules of the country in which the system is operated 

apply first and foremost.
In Germany, for example, the current radiation protection ordinance 

(StrlSchV) based on the Atomic Energy Law (AtG) applies.
The following points are important for measurement with radiometric 

methods:

A handling permit is required for operation of a system using gamma 

rays. This permit is issued by the respective government office or the 

responsible authority (in Germany, for example, offices for environ-

mental protection, trade supervisory boards, etc.)
You can find further instructions in the operating instructions manual 

of the source container.

When handling radioactive sources, unnecessary radiation exposure 

must be avoided. An unavoidable radiation exposure must be kept as 

low as possible. Take note of the following three important measures:

1

2

3

Fig. 2: Measures for protection against radioactive radiation
1 Shielding

2 Time

3 Distance

Functional principle

Handling permit

General instructions for 

radiation protection

Содержание FIBERTRAC 31





























Отзывы: