VeEX VePAL TX300M Скачать руководство пользователя страница 77

Страница: 77 / 421

7.1.2 Errors and Alarms

The Error/Alarm tab brings up several pages showing the errors and alarm status. Alarms/Errors results provides an overview of

all the Errors and Alarms applicable to the signal or network under test. The color of the page tab is normally blue; however, it

will turn red when an alarm error condition has been detected or recorded.

The soft LEDs on screen are arranged logically and will depend on signal hierarchy, structure, payload and framing selected. The

soft LEDs have a tricolor function:

Green:

No error or alarm is present

Red:

An error or alarm condition is detected and is currently present

Yellow:

Indicates a history condition. An error or alarm was detected during the measurement interval but it is no longer

present or active

Errors/Alarms (Page 1)

Note:

Tapping the individual soft LED will automatically link directly to the applicable result screen which provides detailed

information.

Go back to top

Go back to TOC

TX300S_e-manual_D07-00-064P_RevA00

Содержание VePAL TX300M






































































































































































































































































































































































































































Результаты поиска

Содержание VePAL TX300M

Отзывы:

Похожие инструкции для VePAL TX300M

Бренды по названию

Популярные бренды

VeEX VePAL TX300M, Руководство пользователя

Результаты поиска

Содержание VePAL TX300M

Отзывы:

Похожие инструкции для VePAL TX300M

Бренды по названию

Популярные бренды