VeEX VePAL TX300M Скачать руководство пользователя страница 416

Страница: 416 / 421

18.0 Profiles

Profiles can be created in any application that has a "Profiles" drop-down menu available. The PDH, SDH, OTN, Ethernet and

Fiber Channel applications all have the ability to save profiles.

Profiles can be viewed and loaded in the Profiles folder located in the Files folder structure.

Accessing and Configuring Profiles

To access the Profiles menu from the

OTN/SDH/SONET

Testing main menu, tap on the following icons:

Advanced Mode

Profiles

. To save a new profile from the PDH or SDH applications mentioned above, select the

Save as

drop-down option. This

will bring up an alphanumeric keypad to name the profile. When the profile is saved, all of the test configurations that apply to the

particular application are saved. This allows for fast access to preconfigured test configurations.

Alphanumeric keypad

Go back to top

Go back to TOC

TX300S_e-manual_D07-00-064P_RevA00

Содержание VePAL TX300M






































































































































































































































































































































































































































Результаты поиска

Содержание VePAL TX300M

Отзывы:

Похожие инструкции для VePAL TX300M

Бренды по названию

Популярные бренды

VeEX VePAL TX300M, Руководство пользователя

Результаты поиска

Содержание VePAL TX300M

Отзывы:

Похожие инструкции для VePAL TX300M

Бренды по названию

Популярные бренды