VeEX VePAL TX300M Скачать руководство пользователя страница 371

Страница: 371 / 421

15.7 Monitor (Pass Through)

Test Port Selection

Pass through monitor mode enables the test set to be used for long term in-service testing. This allows for bi-directional monitoring of

up to full gigabit Ethernet line rate on the two 1000Base-X ports or the two 10/100/1000T ports.

The Pass Through functionality allows:

In-line traffic monitoring in both directions

Long or short term network monitoring for troubleshooting network traffic problems

Isolate network problems to the customer network or the service provider/operator network

Monitor traffic between 1000Base-X links or 10/100/1000T links

Pass through monitor operation

Pass Through Monitor Copper 1GE

Pass Through Monitor Fiber 1GE

Pass through monitor mode enables bidirectional monitoring between the two 1000Base-X ports or the two 10/100/1000

Base-T ports

Go back to top

Go back to TOC

15.7.1 Setup

The pass through monitor setup and operation is straight forward and simple:

Press the

Test Port

button on the right side of the screen and select a pass through mode option

Connect to both 1000Base-X fiber ports (port 1 and port 2) or both 10/100/1000T copper ports (port 1 and port 2), depending

on the interfaces to be monitored

Once the cable/interface connections are in place, press

Start

Monitor Mode Setup

TX300S_e-manual_D07-00-064P_RevA00

Содержание VePAL TX300M






































































































































































































































































































































































































































Результаты поиска

Содержание VePAL TX300M

Отзывы:

Похожие инструкции для VePAL TX300M

Бренды по названию

Популярные бренды

VeEX VePAL TX300M, Руководство пользователя

Результаты поиска

Содержание VePAL TX300M

Отзывы:

Похожие инструкции для VePAL TX300M

Бренды по названию

Популярные бренды