VeEX VePAL TX300M Скачать руководство пользователя страница 288

Страница: 288 / 421

IP TOS (for Quality of Service testing):

Legacy TOS (Precedence):

The first three bits of the IP TOS field can be edited:

000 - Best Effort

001 - Bulk Data

010 - Transactional

011 - Call Signaling

100 - Streaming Video

101 - Voice

110 - Routing

111 - Reserve

DSCP (Differentiated Services Code Point):

The first six bits of the IP TOS can be edited to provide more

granular service classification.

For more information on the definition of DSCP field in IPv4 and IPv6 headers, refer to

RFC2474

Time To Live (TTL):

Configurable in the range 0 to 255.

Fragment offset byte:

Configurable in the range 0 to 65.528.

Note:

The fragment offset field, measured in units of eight-byte blocks, is 13 bits long and specifies the

offset of a particular fragment relative to the beginning of the original unfragmented IP datagram.

Protocol field:

UDP (0x11), TCP (0x06), User Defined.

BERT Setup - IP Address settings (Layer 3

)

Go back to top

Go back to TOC

Data Tab:

User selects a test pattern that will be encapsulated in the Ethernet frame payload (for framed mode).

Depending on the test layer, different test pattern options are available.

Layer 1 Framed Test Patterns

CRPAT:

Compliant Random Pattern provides broad spectral content and minimal peaking for the

measurement of jitter at component or system level.

CJTPAT:

Compliant Jitter Test Pattern is a Jitter Tolerance Pattern that stresses a receiver by exposing it to

extreme phase jumps thereby stressing the clock data recovery (CDR) circuitry. The pattern alternates

between repeating low transition density patterns and repeating high transition density patterns.

CSPAT:

Compliant Supply Noise Pattern. Represents worst case power supply noise.

BERT Setup - Data selection (Layer 1 Framed)

TX300S_e-manual_D07-00-064P_RevA00

Содержание VePAL TX300M






































































































































































































































































































































































































































Результаты поиска

Содержание VePAL TX300M

Отзывы:

Похожие инструкции для VePAL TX300M

Бренды по названию

Популярные бренды

VeEX VePAL TX300M, Руководство пользователя

Результаты поиска

Содержание VePAL TX300M

Отзывы:

Похожие инструкции для VePAL TX300M

Бренды по названию

Популярные бренды