VeEX VePAL TX300M Скачать руководство пользователя страница 133

Страница: 133 / 421

8.0 Alarm Generation and Error Insertion

Accessing Alarm Generation and Error Insertion

On the TX300, tap on Home (main menu) >

Advanced Mode

Alarm/Error

On the TX300e, tap on Home (main menu) >

Alarm/Error

The alarm and error functions are used in conjunction with the drop-down menu which has dedicated buttons for error injection

and alarm generation. Alarm and error selections will depend on PDH, SDH, or OTN signal types.

Alarm Setup

Go back to top

Go back to TOC

8.1 Alarm Generation

Generation range of different anomalies into the transmit signal. Alarm generation modes include:

Alarm Flow

Continuous:

Generates a continuous alarm when button is tapped

Count:

Specific count for 0.1s, 1s, 10s, 100s when button is tapped

Alarm/Error Generation

TX300S_e-manual_D07-00-064P_RevA00

Содержание VePAL TX300M






































































































































































































































































































































































































































Результаты поиска

Содержание VePAL TX300M

Отзывы:

Похожие инструкции для VePAL TX300M

Бренды по названию

Популярные бренды

VeEX VePAL TX300M, Руководство пользователя

Результаты поиска

Содержание VePAL TX300M

Отзывы:

Похожие инструкции для VePAL TX300M

Бренды по названию

Популярные бренды