background image

1

  

Introduction 

This manual discusses removal of a TLS-350 console and replacing it with a TLS-450PLUS console. The instruc-
tions assume all site monitoring devices have been previously installed and site wiring is complete.

Contractor Certification Requirements

Veeder-Root requires the following minimum training certifications for contractors who will install and setup the 
equipment discussed in this manual:

Installer Certification (Level 1):

 Contractors holding valid Installer Certification are approved to perform wiring 

and conduit routing; equipment mounting; probe, sensor and carbon canister vapor polisher installation; wireless 
equipment installation; tank and line preparation; and line leak detector installation.

Technician Certification (Level 2/3):

 Contractors holding valid Technician Certifications are approved to 

perform installation checkout, startup, programming and operations training, system tests, troubleshooting and 
servicing for all Veeder-Root Series Tank Monitoring Systems, including Line Leak Detection. In addition, 
Contractors with the following sub-certification designations are approved to perform installation checkout, startup, 
programming, system tests, troubleshooting, service techniques and operations training on the designated system. 

• Wireless 2
• Tall Tank

Warranty Registrations

 may only be submitted by selected Distributors.

Safety Precautions

The following safety symbols may be used throughout this manual to alert you to important safety hazards and 
precautions

EXPLOSIVE

Fuels and their vapors are extremely explosive if ignited.

FLAMMABLE

Fuels and their vapors are extremely flammable.

ELECTRICITY

High voltage exists in, and is supplied to, the device. A 
potential shock hazard exists.

TURN POWER OFF

Live power to a device creates a potential shock hazard. 
Turn Off power to the device and associated accessories 
when servicing the unit.

WARNING

Heed the adjacent instructions to avoid damage to 
equipment, property, environment or personal injury.

READ ALL RELATED MANUALS

Knowledge of all related procedures before you begin 
work is important. Read and understand all manuals thor-
oughly. If you do not understand a procedure, ask some-
one who does.

USE SAFETY BARRICADES

Unauthorized people in the work area are dangerous. 
Always use safety cones or safety tape to block access 
to the work area.

STATIC SENSITIVE COMPONENTS

Wear grounded anti-static wrist strap before handling 
the printed circuit board and mounted components.

OFF

Содержание TLS-350l















Отзывы: