background image

Installation

Starting the System and Completing the Installation

17

Disconnect, lock out, and tag power at the panel before servicing the pump and taking 
these resistance readings.

When servicing equipment, use non-sparking tools and use caution when removing or in-
stalling equipment to avoid generating a spark.

Table B.  

Bury 

Depth 

“A”

Riser Length 

“B”

Tank Diameters “C” / Pump Length Requirements “D”

30”

10” (883-442-1)

C = 72” / D = 78”

C = 84” / D = 90”

C = 96” / D = 102”

C = 120” / D = 126”

C = 144” / D = 150”

36”

16” (883-445-1)

C = 72” / D = 84”

C = 84” / D = 96”

C = 96” / D = 108”

C = 120” / D = 132”

C = 144” / D = 156”

42”

21” (883-449-1)

C = 72” / D = 89”

C = 84” / D = 101”

C = 96” / D = 113”

C = 120” / D = 137”

C = 144” / D = 161”

48”

27” (883-449-1)

C = 72” / D = 95”

C = 84” / D = 107”

C = 96” / D = 119”

C = 120” / D = 143”

C = 144” / D = 167”

60”

36” (883-451-1)

C = 72” / D = 104” C = 84” / D = 116”

C = 96” / D = 128”

C = 120” / D = 152”

C = 144” / D = 176”

72”

51” (883-454-1)

C = 72” / D = 119” C = 84” / D = 131”

C = 96” / D = 143”

C = 120” / D = 167”

C = 144” / D = 191”

Table C.  

Model Number 

Pump Motor 

Assembly

HP

Volt

Phase

Winding Resistances (Ohms)

Orange to Red

Orange to 

Black

Red to Black

Blue to Blue

UMP200J1-2MB

2

208-230

1

5.4 - 6.6

1.6 - 2.0

7.0 - 8.6

0.0 - 1.0

UMP200J4-2MB

2

208-230

3

2.6 - 3.3

2.6 - 3.3

2.6 - 3.3

0.0 - 1.0

UMP300J4-2HB

3

208-230

3

1.9 - 2.3

1.9 - 2.3

1.9 - 2.3

0.0 - 1.0

UMP300J17-3HB

3

380-415

3

7.6 - 9.3

7.6 - 9.3

7.6 - 9.3

0.0 - 1.0

UMP500J4-2K

5

208-230

3

1.0 - 1.3

1.0 - 1.3

1.0 - 1.3

0.0 - 1.0

UMP500J17-3K

5

380-415

3

4.0 - 4.9

4.0 - 4.9

4.0 - 4.9

0.0 - 1.0

UMP500J6-2K

5

575

3

6.3 - 7.6

6.3 - 7.6

6.3 - 7.6

0.0 - 1.0

NOTE: The above readings do not include the added resistance of the power supply wires to the submersible pump. Therefore, for 
the readings to fall within the above limits, the resistance should be checked at the submersible pump junction box. If the resis-
tance readings are taken at the control box or magnetic starter, they will be sightly higher.

WARNING

NOTICE

Содержание Red Jacket Maxxum Big-Flo Quick-Set P200R1



















































Отзывы: