background image

EMR

3

 Setup and Operation Manual

C&C Mode Setup Categories

40

Auto Calibrate

Figure 42 illustrates meter Auto Calibration (single point) setup procedure.

Figure 42. Meter Auto Calibration Setup

MultiCalibrate

Figure 43 illustrates meter MultiCalibration setup procedure.

Figure 43. Meter MultiCalibration Setup

Press ENTER to accept
entry.  Press button until you
return to METER CALIBRTN.

Press ENTER to 

return to 

PROD CAL 1

ENTER

ENTER

AUTO CALIBRATE

START DISPENSE

DISPENSING

NEXT

Note: Dispense product into
a proving can, then press finish
when you have dispensed a
calibrated amount.

START

ENTER NTC VOL

Note:  Enter volume dispensed
into proving can for NTC VOL

FINISH

Press up/down arrows
to scroll through the
numbers, and NEXT
to move from one 
digit to the next.  

Press ENTER to accept
entry and return to 

ENTER

ENTER

MULTICALIBRATE

START DISPENSE

DISPENSING

NEXT

NEXT

START

ENTER NTC VOL

FINISH

 

CALB RATE 1

CALB RATE 8

+

-

+

Note:  In this multipoint calibration option you dispense at  
up to 8 different flow rates. These rates are determined by 
how much you squeeze the nozzle handle during each 
calibration.
For example, the first rate you dispense product at a very 
slow rate, but for each of the additional calibration rates 
you increase the flow.  Once calibration is complete, the 
EMR3 will calculate the amount of product dispensed 
based on interpolation.

Note: Dispense product into a proving 
can for the calibration rate. While 
dispensing, the flow rate will appear in 
the Register Field and the Volume will 
appear in the Preset Field. Stop when 
you have dispensed a calibrated 
amount.

Note:  read/observe proving can 
volume for this calibration rate 
and enter that volume here. Press 
up/down arrows to scroll through 
the numbers, and NEXT to move 
from one digit to the next. 

Empty proving can and repeat this 
procedure for Calb Rate 2. Continue until 
the desired number of Calibration Rates 
are complete. When finished the desired 
number press ENTER until you return to 
METER CALIBRTN.

Press ENTER to 

return to 

PROD CAL 1

Содержание EMR3 XStream-PKG







































































Отзывы: