background image

Locate the 2SC2498 plastic transistor and note its flat side.  Position at Q1, as indicated 
by the outline on the pc board.  Gently pre-form the leads so the case is spaced 
approximately .15" above the pc board surface when leads are fully inserted (see below).  
 

                                                     

2SC

2498

  

 
[  ]  Install the 2SC2498 at Q1 and solder.   
 
Your kit has six (6) jumper wires to install.  Each should be pre-formed from a bare 
length of discarded component lead, as shown below.  The approximate distance between 
mounting holes is given to help you pre-form each one.  When installed, each jumper 
should lay flat against the PC board. 
 

                                         

span

discarded lead end

 

 
[  ]  Make a jumper with a .2" span.  Install at JMP1 and solder. 
[  ]  Make a jumper with a .25" span.  Install at JMP2 and solder. 
[  ]  Make another jumper with a .25" span.  Install at JMP3 and solder. 
[  ]  Make a jumper with a .3" span.  Install at JMP4 and solder. 
[  ]  Make a second jumper with a .3" span.  Install at JMP5 and solder.  
[  ]  Make a third jumper with a .3" span.  Install at L3* and solder. 
 

*Important Note:  

Inductor L3 is not used with the 49 MHz version of this kit.  A jumper 

is used in its place.  
 
Locate the 10.7-MHz ceramic filter (looks like a square disc-ceramic capacitor with three 
pins, marked 10.7J).  This part is unpolarized and may be installed either way. 
 
[  ]  Install the 10.7-MHz filter at FL1 and solder.   
 
Locate the 455-kHz ceramic filter (a small black cube with three pins marked 55D or 
55F).  This it will only fit one way on the PC board. 
 
[  ]  Install the 455-kHz filter at FL2 and solder. 
 
[  ]  Find the 3.5 mm stereo mini-headphone jack.  Install and solder at J2. 
 
[  ]  Find the RCA phono jack.  Install at J1 and solder all four taps. 
 
[  ]  Locate push-button power switch SW1.  Install at SW1 and solder. 
 

Содержание VEC-1016K
























Отзывы: