background image

01/16

1-6

4

12

13

GB

INSTALLATION INSTRUCTIONS: Viewline 52 mm

TU00-0752-8707102

Technische Änderungen vorbehalten  -  Technical details subject to change

TU00-0752-8707102

Ammeter

Use the following connector to connect the instrument: Connector set, 

8-pin - A2C59510850 

The connector set is designed for a cable cross-section of 0.25 - 0.5 mm². 

For other cross-sections, please use contacts made by Tyco.

Single contacts:  

Tyco No. 1355718-1 for 0.14 – 0.22 mm²

 

Tyco No. 963729-1 for 0.5 – 0.75 mm²

Strip:  

Tyco No. 1355717-1 for 0.14 – 0.22 mm²

 

Tyco No. 963715-1 for 0.5 – 0.75 mm²

Create a crimp connection using the contacts and the corresponding 

cables. Follow the instructions of the hand pliers manufacturer. 

Use the following for this: 

Hand pliers  

Tyco No. 539635-1 

and the tool  

Tyco No. 539682-2 for these hand pliers

Pay special attention to whether the crimp barrel clutches all individual 

wires in the cable, otherwise you risk a short circuit!

Connector set, 8-pin 

A2C59510850

Designations in the wiring diagram:

30 - terminal 30 - steady-state plus 12/24 V

15 - terminal 15 - connected (ignition) plus

58 - terminal 58 - lighting

31 - terminal 31 - ground

A1 - alternator

B1 - battery

FX - fuse

K1 - switch “ignition”

S1 - starter

You must comply with the wiring diagram.

Electrical connection:

•  Note cable cross-sectional area! 
•  Reducing the cable cross-sectional area leads to higher current den-

sity, which can cause the cable cross-sectional area in question to 

heat up! 

•  When installing electrical cables, use the provided cable ducts and 

harnesses; however, do not run cables parallel to ignition cables or to 

cables that lead to large electricity consumers. 

•  Fasten cables with cable ties or adhesive tape. Do not run cables over 

moving parts. Do not attach cables to the steering column! 

•  Ensure that cables are not subject to tensile, compressive or shearing 

forces. 

•  If cables are run through drill holes, protect them using rubber sleeves 

or the like. 

•  Use only one cable stripper to strip the cable. Adjust the stripper so 

that stranded wires are not damaged or separated. 

•  Use only a soft soldering process or commercially available crimp con-

nector to solder new cable connections! 

•  Make crimp connections with cable crimping pliers only. Follow the 

safety instructions of the tool manufacturer. 

•  Insulate exposed stranded wires to prevent short circuits. 
•  Caution: Risk of short circuit if junctions are faulty or cables are 

damaged. 

•  Short circuits in the vehicle network can cause fires, battery explo-

sions and damages to other electronic systems. Consequently, all 

power supply cable connections must be provided with weldable 

connectors and sufficiently insulated. 

•  Ensure ground connections are sound. 
•  Faulty connections can cause short circuits. Only connect cables 

according to the electrical wiring diagram. 

•  If operating the instrument on power supply units, note that the 

power supply unit must be stabilized and it must comply with the 

following standard: DIN EN 61000, Parts 6-1 to 6-4.

Wiring diagram without shunt

Power consumer

Содержание Viewline TU00-0752-8707102







Отзывы: