VC VCSBC6438 Скачать руководство пользователя страница 29

Страница: 29 / 39

VCSBC64XX_HW.pdf – Hardware Documentation VCSBC64XX Smart Cameras

6.4.1

Resetting the Camera with help of the VCnet Recovery Tool

A new tool – the “Vcnet Recovery Tool” is provided for resetting the IP address of the TI-based VC

Smart Cameras from VC4XXX. Vcnet Recovery is supported from camera OS VCRT 5.21.

In order to use the VCnet Recovery tool, follow the steps below:

1. Download and install the “

Java(TM) 2 Runtime Environment, Standard Edition 1.4.XX

” on

your PC (Download from

www.sun.com

- > Downloads - > J2SE v 1.4.2_11 JRE ).

Download

VCnet Recovery Tool for VC40XX and VCSBC40XX

from

www.vision–

comp.com

-> Service & Support.

3. Unpack the “vcnet1.2.zip” folder a directory on your hard drive (for instance C:\ti\Util…).

4. Open the Dos command line window and change to the directory containing “vcnet.jar”.

5. Execute the following command from the DOS Window "java -jar vcnet.jar -snr 5912345" , by

specifying the camera serial number as shown. This command sends vcp packets via UDP

broadcast for the next 15 seconds. Sending this command resets the corresponding camera

to the default IP address and bypasses Autoexec execution. Further options below.

6. Boot the corresponding camera (power on) during the next 15 seconds. During start up the

camera listens 0.5 seconds for cvp packets send with vcnet.jar.

7. If a valid vcp packet is received from camera an answer packet is sent (see example below).

The camera continues booting in standard configuration:

Default IP address:

192.168.0.65

Mask: 255.255.255.0

Gateway: none

An autoexec in flash memory is not executed.

Example of resetting a VCSBC40XX, S/N 0100151:

C:\Programme\VCnet>java -jar vcnet.jar -snr 0100151

VCnet Recovering Tool Version 1.2 - Copyright Vision Components 2005

Recovering Serial Number = 100151

Listening on port 67 for incoming packets!

Packet 2 from: /0.0.0.0

===Data as Text:===

model: VC4018E

S/N: 0100151

DC: 06/10/05 09:23:06

MAC: 00-06-1F-01-87-37

IP: 192.168.0.81

MSK: 255.255.255.0

GTW: 192.168.0.1

….

1996-2011 Vision Components GmbH Ettlingen, Germany

Содержание VCSBC6438








































Результаты поиска

Содержание VCSBC6438

Отзывы:

Похожие инструкции для VCSBC6438

Бренды по названию

Популярные бренды

VC VCSBC6438, Руководство по эксплуатации

Результаты поиска

Содержание VCSBC6438

Отзывы:

Похожие инструкции для VCSBC6438

Бренды по названию

Популярные бренды