Vascat MAC QM Скачать руководство пользователя

Страница: 14 / 56

OPERATION AND MAINTENANCE MANUAL

MAC QM MOTORS

PAGE: 14

CODE: CTT42 EDITION: 01 RELEASE: JULY 2016

Subject to technical changes without prior notice

3.3.2

Types of construction

The following are some of the mounting types applicable to the MAC QM motors, labelled in accordance with the IEC/EN 60034/7

standard.

Type of

construction

Enclosure

Mounting

Type of

construction

Enclosure

Mounting

IM B3

IM1001

Foot mounted, on

lower horizontal plane

IM V1

IM3011

Flange mounted,

shaft downward

(with through holes)

IM B5

IM3001

Flange mounted,

horizontally

(with through holes)

IM V3

IM3031

Flange mounted,

shaft downward

(with through holes)

IM B6

IM1051

Foot mounted on

vertical plane

(shaft to the left)

IM V5

IM1011

Foot mounted on

vertical plane

(shaft downward)

IM B7

IM1061

Foot mounted on

vertical plane

(shaft to the right)

IM V6

IM1031

Foot mounted on

horizontal plane

(shaft downward)

IM B8

IM1071

Foot mounted on

horizontal plane

(shaft to the right)

IM V18

IM3611

Flange mounted,

shaft downward

(with threaded holes)

IM B14

IM3601

Flange mounted

(with through holes)

IM V19

IM3631

Flange mounted,

shaft upward

(with threaded holes)

IM B35

IM2001

Flange and foot

mounted

(with through holes)

IM V15

IM2011

Flange mounted, (with

through holes), shaft

downward and feet

IM 6811

Pedestal bearings

without feet

IM V36

IM2031

Flange mounted (with

through holes), shaft

downward and feet

Table 5: Types of construction

Содержание MAC QM

























































Результаты поиска

Содержание MAC QM

Отзывы:

Похожие инструкции для MAC QM

Бренды по названию

Популярные бренды

Vascat MAC QM, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание MAC QM

Отзывы:

Похожие инструкции для MAC QM

Бренды по названию

Популярные бренды