background image

 

14” & 15” Slow Scan Series User Guide                                                                                                                   150-002 

Federal Communications Commission (F.C.C.) Statement 

This device complies with Part 15 of the FCC Rules.  Operation is subject to the following two conditions:    
(1) this device may not cause harmful interference, and  
(2) this device must accept any interference received, including interference that may cause undesired       
operation. 

Accessories:

 

This device has been tested and found to comply with the limits of a Class A digital device, the 

 

accessories associated with this equipment are following: 

• 

Shielded video cable. 

• 

Power Cord. 

These accessories are required to be used in order to ensure compliance with FCC Rules.  It is the            
responsibility of the user to provide and use these accessories. 
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to 
Part 15 of the FCC Rules.  These limits are designed to provide reasonable protection against harmful inter-
ference in a residential installation.  This equipment generates, uses and can radiate radio frequency energy 
and, if not installed and used in accordance with the instructions, may cause harmful interference to radio 
communications.  However, there is no guarantee that interference will not occur in a particular installation.  If 
this equipment does cause harmful interference to radio or television reception, which can be determined by 
turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of 
the following measures: 

• 

Reorient/Relocate the receiving antenna. 

• 

Increase the separation between the equipment and receiver. 

• 

Connect the equipment into an outlet on a circuit different from that to which the receiver is       
connected. 

• 

Consult the dealer or an experienced radio or TV technician for help. 

CAUTION:   Changes or modifications not expressly approved by the manufacturer responsible for 
compliance could void the user's authority to operate the equipment. 

 

DOC Compliance Notice

 

This digital apparatus does not exceed the Class A limits for radio noise emissions from digital apparatus set 
out in the Radio Interference Regulations of the Canadian Department of Communications. 
 

Technical Service Warning for X-ray Radiation Protection:

 

This product contains electrical and mechanical parts essential for X-ray protection.  For replacement        
purposes, use only part types shown in the parts list.  Do not substitute. 

 
 

Содержание VT14A-D














Отзывы: